Ahlborn ALMEMO 2470-1S Скачать руководство пользователя страница 16

Страница: 16 / 48

7. Power supply

bar indicates the approximate charge status. While the 3 green sections flash

left to right, the rechargeable batteries are being charged. As soon as all 3

sections remain green, the rechargeable batteries are fully charged; however,

the mains adapter can be left connected to the device. If standard non-re-

chargeable batteries are being used, the battery symbol will, as soon as the

mains adapter is connected, flash briefly in red. Standard non-rechargeable

batteries must not be subjected to recharging; charging must be terminated im-

mediately by pressing any key; the device will then be powered by mains only.

7.4 External DC voltage supply

The DC socket (3) can also be used to connect another DC voltage, 5 to 13 V

(minimum 200 mA). It can be connected using ALMEMO

plug ZA1000-FSV. If,

however, the power supply has to be electrically isolated from the transducers,

then electrically isolated DC cable ZA 2690-UK must be used. It will then be pos-

sible to use the measuring instrument in a 12-volt or 24-volt on-board supply sys-

tem.

7.5 Sensor supply

At the ter (plus) and - (minus) in the ALMEMO

plug there is a config-

urable sensor supply voltage available (self-healing fuse, 500 mA). The sensor

voltage supplied by the device is set automatically, depending on the minimum

supply voltage requirements of the sensors, 6V (400 mA), 9 V (300 mA), or 12

V (200 mA). (see Manual, Section 6.10.5) Other voltages (15 V, 24 V, or refer-

ences for a potentiometer and strain gauge) can also be obtained using special

plugs. (see Manual. Sections 4.2.5 and 4.2.6).

7.6 Switching ON / OFF, reinitialization

The

ON OFF

key (6) is located in the middle of the keypad; to switch the

device ON press briefly and release; to switch the device OFF press and hold

down. When the device switches OFF all saved values and settings are re-
tained intact. (

see 7.7

) While rechargeable batteries are being charged by a

mains adapter the device cannot be switched OFF (display ´

noOFF

´). To switch

OFF in these circumstances the device will have to be disconnected. If inter-

ference (e.g. electrostatic) or a malfunction (e.g. battery failure) causes the

device to behave abnormally, it can be reinitialized. To activate a reset press
and hold down key

FCT

when switching on - without mains adapter connected.

This will restore all settings - except the device designation - to factory default

status. Programming of sensors in the ALMEMO

plugs will also remain unaf-

fected.

16 ALMEMO 2470

Содержание ALMEMO 2470-1S

















































Результаты поиска

Содержание ALMEMO 2470-1S

Отзывы:

Похожие инструкции для ALMEMO 2470-1S

Бренды по названию

Популярные бренды

Ahlborn ALMEMO 2470-1S, Руководство по эксплуатации

Результаты поиска

Содержание ALMEMO 2470-1S

Отзывы:

Похожие инструкции для ALMEMO 2470-1S

Бренды по названию

Популярные бренды