background image

43

USER MANUAL

Check if the vehicle’s capacity is adequate to the weight of the machine which 

is indicate in the serial label fi tted to the frame of the sprayer.

WARNING: the weight indictaed in the serial nr. label is referred to the m 

chine a full load with the liquid.

Make sure to respect the limits foreseen by the rules of road circulation.
Adequately fasten the machine and detached parts.

It is advisable to transport the sprayer always with the tank completely empty 

and clean. Make sure of not spilling anything on the truck and/or on the road.
Make sure to respect the limits foreseen by the rules of road circulation.

When transporting the machine over short or long distances, it is advisable to
drain the fuel tank and chemicals tank completely so as to avoid leakage.

During transport the machine should always be kept in a natural position, as 

there is always some residue of fuel in the tank which could leak out and im-

pregnate and/or damage the components of the sprayer and in order to re-

spect the enviroment.

WARNING: before transporting the machine, wait until the motor unit has 

cooled down so as to avoid burning yourself or damaging material in the vicin-

ity of the machine.

It is advisable top avoid lifting the sprayer in other points such as the tank, 

pump, regulator valve or spraying units like nozzles, hoses, as this could break 
or damage some of the components.

Be careful to lock accurately the machine to the truck or pick-up to avoid

unnecessary and/or dangerous movements during the transit. Check all the 
parts which may get loose and lock them accordingly.

TRANSPORT

Содержание DELTA
















































Отзывы: