Agria 1000 Скачать руководство пользователя страница 31

Страница: 31 / 36

agria

Power Hoe 1000

5. Maintenance

Storage

For longer periods of no operation prepare the power hoe for storage. Pro-
ceed as follows:

a) Clean thoroughly

Repair paint coat

b) Spray all shining parts and hoeing tools with bio-slushing oil.

c) Engine preservation

Drain fuel completely or fill fuel tank and add fuel stabilizer (agria-No. 799 09)

- observe enclosed instructions! Let engine run for approx. 1 minute.

Change the engine oil.

Fill a tea-spoon (approx. 0.03l) of engine oil into the spark plug opening. Slowly

crank the engine.

Reinstall the spark plug and set the piston to compression with the recoil starter

to keep the valves closed.

Slowly crank the engine after every 2–3 weeks (spark-plug connector is re-

moved). Then set the piston to compression again.

d) Parking and storing

To park, transport, or store the power hoe, do not tilt it for-
ward. When positioned at a forward angle, engine oil may
get into the cylinder and into the combustion chamber, which
may result in starting problems and heavy oil carbonization.

e) Storage

Because of severe corrosion

do not park the machine

- in humid rooms

- in rooms where fertilizer is stored

- in stables or adjacent rooms.

f) Protect the machine

with cloth or a similar cover.

Содержание 1000





































Результаты поиска

Содержание 1000

Отзывы:

Похожие инструкции для 1000

Бренды по названию

Популярные бренды

Agria 1000, Руководство по эксплуатации

Результаты поиска

Содержание 1000

Отзывы:

Похожие инструкции для 1000

Бренды по названию

Популярные бренды