Agilent Technologies U1270 Series Скачать руководство пользователя | Manualshive

Страница: 24 / 65

background image

1

Calibration Procedures

Basic Operating Test

24

U1270 Series Service Guide

The alert beep tone will continue to beep until the test lead
is removed from the

A

terminal or until the rotary switch is

set to the

function.

Input warning test (µA mA terminal)

The multimeter sounds a continuous alert beep when the
test lead is inserted into the

µA mA

terminal but the rotary

switch is not set to the

or

function.

The multimeter displays an input warning error (

Figure 1- 4

).

Figure 1-4

Input warning display (µA mA terminal)

The alert beep tone will continue to beep until the test lead
is removed from the

µA mA

terminal or until the rotary

switch is set to the

or

function.

N O T E

Before conducting this test, ensure that the beep function is not disabled
in the multimeter’s setup.

N O T E

Before conducting this test, ensure that the beep function is not disabled
in the multimeter’s setup.

«
...
22
23
24
25
26
...
»

Содержание U1270 Series


































































Отзывы:

Нет отзывов

Похожие инструкции для U1270 Series

Бренд: Black Box Страницы: 2

Бренд: IDEAL Страницы: 19

Бренд: Chauvin Arnoux Страницы: 64

Бренд: GTC Страницы: 2

Бренд: King Tony Страницы: 82

Бренд: Micro Seven Страницы: 6

Бренд: Utilita Страницы: 37

Бренд: Gossen MetraWatt Страницы: 20

Бренд: Perel Страницы: 20

Бренд: Perel Страницы: 36

Бренд: Keysight Страницы: 57

Lilliput HDS2062M-N

Бренд: Owon Страницы: 74

Бренд: koban Страницы: 80

Бренд: koban Страницы: 72

Бренд: koban Страницы: 98

Бренд: DynaMetric Страницы: 2

Бренд: Radio Shack Страницы: 20

FlexDMM PXI-4070

Бренд: National Instruments Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды