manualshive.com logo in svg

Agilent Technologies U1270 Series, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies U1270 Series Скачать руководство пользователя страница 64

2

Service and Maintenance

 

Obtaining Repair Service (Worldwide)

64

U1270 Series Service Guide

Obtaining Repair Service (Worldwide)

To obtain service for your instrument (in- warranty, under 
service contract, or post- warranty), contact your nearest 
Agilent Service Center. They will arrange to have your unit 
repaired or replaced, and can provide warranty or 
repair- cost information where applicable.

To obtain warranty, service, or technical support information 
you can contact Agilent at one of the following telephone 
numbers:

•

In the United States: (800) 829- 4444

•

In Europe: 31 20 547 2111

•

In Japan: 0120- 421- 345

Or use our Web link for information on contacting Agilent 
worldwide: 

www.agilent.com/find/assist

Or contact your Agilent representative.

Before shipping your instrument, request the Agilent Service 
Center to provide shipping instructions, including what 
components to ship. Agilent recommends that you retain the 
original shipping carton for use in such shipments.

Содержание U1270 Series


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды