manualshive.com logo in svg

Agilent Technologies U1270 Series, Руководство по обслуживанию

Поделиться
Скачать
Agilent Technologies U1270 Series Скачать руководство пользователя страница 57

Service and Maintenance

2

 

Fuse Replacement

U1270 Series Service Guide

57

Fuse Replacement

The current input terminals of your multimeter are fuse 
protected. The fuses are located next to the battery 
compartment. 

•

The 

µA mA

 terminal is protected by a 10 

×

 35 mm 

 

440 mA/1000 V 30 kA fast- acting fuse (Fuse 1).

•

The 

A

 terminal is protected by a 10 

×

 38 mm 

 

11 A/1000 V 30 kA fast- acting fuse (Fuse 2).

If you are certain that the fuse is faulty, replace it with one 
of the same size and rating.

1

Open the battery cover.

 Lift the tilt stand and loosen 

screws with a suitable Phillips screwdriver and remove 
the battery cover.

2

Locate the faulty fuse.

 Fuse 1 (see 

Figure 2- 3

) is located 

to the right of batteries, and Fuse 2 (see 

Figure 2- 4

) is 

located at the bottom of the batteries. See 

Figure 2- 5

 for 

the specific location, size, and ratings of Fuse 1 and 2.

Gently remove the defective fuse by prying one end of the 
fuse with a flathead screwdriver and removing it out of 
the fuse bracket. Replace a new fuse of the same size and 
rating into the center of the fuse holder.

3

Close the batter cover.

 Place the battery cover back in its 

original position and tighten the screws.

N O T E

No recalibration is required after replacing the fuse.

C A U T I O N

Before you proceed with the fuse replacement, remove all cable 
connections to the terminals and ensure that the rotary switch is at the 
OFF position.

Содержание U1270 Series


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды