Agilent Technologies U1270 Series Скачать руководство пользователя страница 6

Страница: 6 / 65

U1270 Series Service Guide

Environmental Conditions

This instrument is designed for indoor use and in an area with low
condensation. The table below shows the general environmental
requirements for this instrument.

Environmental conditions

Requirements

Temperature

• Operating condition

•

U1271A/U1272A/U1273A: –20 °C to 55 °C

•

U1273AX: –40 °C to 55 °C (using Lithium
batteries)

• Storage condition

•

–40°C to 70 °C

Humidity

• Operating condition

•

Maximum: 80% RH at 40 °C
(non-condensing)

•

Minimum: 50% RH at 40 °C
(non-condensing)

• Storage condition

•

Up to 95% RH at 40 °C (non-condensing)

Altitude

Up to 3000 m

Pollution degree

Pollution degree II

N O T E

The U1270 Series Handheld Digital Multimeters comply with the following safety
and EMC requirements:

• Safety

•

EN/IEC 61010-1:2001

•

ANSI/UL 61010-1:2004

•

CAN/CSA-C22.2 No. 61010-1-04

• EMC

•

IEC61326-1:2005/EN61326-1:2006

•

Canada: ICES/NMB-001: Issue 4, June 2006

•

Australia/New Zealand: AS/NZS CISPR 11:2004

Содержание U1270 Series


































































Результаты поиска

Содержание U1270 Series

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies U1270 Series, Руководство по обслуживанию

Результаты поиска

Содержание U1270 Series

Отзывы:

Бренды по названию

Популярные бренды