Agilent Technologies N6700B Скачать руководство пользователя страница 189

Страница: 189 / 206

Service Appendix D

Series N6700 User’s Guide

189

Command

Errors

(continued)

−

160

Block data error

Generic block data error

−

161

Invalid block data

The number of data bytes sent does not match the number of bytes specified in the header.

−

168

Block data not allowed

Data was sent in arbitrary block format but is not allowed for this command.

−

170

Expression error

Generic expression error

−

171

Invalid expression data

The expression data element was invalid.

−

178

Expression data not allowed

Expression data element was sent but is not allowed for this command.

Execution

Errors

(these errors set Standard Event Status register bit #4)

−

200

Execution error

Generic syntax error

−

220

Parameter error

A data element related error occurred.

−

221

Settings conflict

A data element could not be executed because of the present instrument state.

−

222

Data out of range

A data element could not be executed because the value was outside the valid range.

−

223

Too much data

A data element was received that contains more data than the instrument can handle.

−

224

Illegal parameter value

An exact value was expected but not received.

−

225

Out of memory

The device has insufficient memory to perform the requested operation.

−

226

Lists not same length

One or more lists are not the same length.

−

230

Data corrupt or stale

Possible invalid data. A new reading was started but not completed.

−

231

Data questionable

The measurement accuracy is suspect.

−

232

Invalid format

The data format or structure is inappropriate.

−

233

Invalid version

The version of the data format is incorrect to the instrument.

−

240

Hardware error

The command could not be executed because of a hardware problem with the instrument.

−

241

Hardware missing

The command could not be executed because of missing hardware, such as an option.

−

260

Expression error

An expression program data element related error occurred.

−

261

Math error in expression

An expression program data element could not be executed due to a math error.

Содержание N6700B















































































































































































































Результаты поиска

Содержание N6700B

Отзывы:

Agilent Technologies N6700B, Руководство пользователя, Страница: 189 / 206

Результаты поиска

Содержание N6700B

Отзывы: