90 Calibration
Program Listing for "B" Modules (continued)
1040
!
1050
SUB Cal_res(@Ld,Chan,Res_rng,Res_hipt,Res_lopt,Flag)
1060
PRINT "RESISTANCE CALIBRATION, RANGE";Res_rng
1070
PRINT "Set power supply to calibration information table"
1080
PRINT "Press CONT when ready to continue"
1090
PAUSE
1100
OUTPUT @Ld;"CHAN";Chan
1110
OUTPUT @Ld;"MODE:RES"
1120
OUTPUT @Ld;"RES:RANG";Res_rng
1130
OUTPUT @Ld;"RES";Res_hipt
1140
INPUT "Enter voltage across input terminals in volts",Hipt_volt
1150
INPUT "Enter current through current shunt in amps”,Hipt_curr
1160
Hipt_res=Hipt_volt/Hipt_curr
1170
OUTPUT @Ld;"CAL:LEV:HIGH";Hipt_res
1180
OUTPUT @Ld;"RES";Res_lopt
1190
INPUT "Enter voltage across input terminals in volts",Lopt_volt
1200
INPUT "Enter current through current shunt in amps",Lopt_curr
1210
Lopt_res=Lopt_volt/Lopt_curr
1220
OUTPUT @Ld;"CAL:LEV:LOW;Lopt_res
1230
PRINT "Test unit to verify resistance values"
1240
PRINT "Press CONT when ready to calibrate transient level"
1250
PAUSE
1260
IF Flag THEN
1270
OUTPUT @Ld;"RES";Res_hipt
1280
ELSE
1290
OUTPUT @Ld;"RES";Res_lopt
1300
END IF
1310
OUTPUT @Ld;"TRAN:STAT ON;MODE TOGG;:TRIG:SOUR BUS"
1320
IF Flag THEN
1330
OUTPUT @Ld;"RES:TLEV";Res_lopt
1340
ELSE
1350
OUTPUT @Ld;"RES:TLEV";Res_hipt
1360
END IF
1370
OUTPUT @Ld;"*TRG"
1380
INPUT "Enter voltage across input terminals in volts",Tran_volt
1390
INPUT "Enter current through current shunt in amps",Tran_curr
1400
Tran_res=Tran_volt/Tran_curr
1410
OUTPUT @Ld;"CAL:TLEV";Tran_res
1420
OUTPUT @Ld;"TRAN OFF"
1430
PRINT "Test unit to verify transient values are in spec"
1440
PRINT "Press CONT when ready to end program or calibrate next range"
1450
PAUSE
1460
SUBEND
Содержание 6050A
