Calibration 81
Program Listing for "A" Modules
10
Load=705
20
Chan= 1
30
OUTPUT Load;"CHAN";Chan;";CAL ON"
40
Cal_curr(Load,Chan,Hi_curr_rng,Hi_curr_hipt,Hi_curr_lopt,l);
50
Cal_curr(Load,Chan,Lo_curr_rngLo_cu,rr_hipt,Lo_curr_lopt,0)
60
Cal_volt(Load,Chan,Volt_hipt,Volt_lopt)
70
Cal_res(Load,Chan,Lo_res_rng,Lo_res_hipt,Lo_res_lopt,0)
80
Cal_res.(Load,Chan,Mid_res_rng,Mid_res_hipt,Mid_res_lopt,l)
90
Cal_res(Load,Chan,Hi_res_rng,Hi_res_hipt,Hi_res lopt,l),
100
OUTPUT Load;l"CAL:SAVE"
110
OUTPUT Load;"CAL OFF"
120
END
130
!
140
SUB Cal_curr(Load,Chan,Curr_rng,Curr_hipt,Curr_lopt,Flag)
150
PRINT "CURRENT CALIBRATION, RANGE ";Curr_rng
160
PRINT "Set power supply according to module calibration table"
170
PRINT "Use the correct current shunt for the range you are calibrating"
180
PRINT "Press CONTINUE when ready"
190
PAUSE
200
OUTPUT Load;"CHAN";Chan
210
OUTPUT Load;"MODE:CURR"
220
OUTPUT Load;"CURR:RANG";Curr_rng
230
OUTPUT Load;"CURR";Curr_hipt
240
IF Flag THEN WAIT 30
250
INPUT "Enter current through shunt for high point in amps",Hipt_curr
260
OUTPUT Load;"CAL:LEV:HIGH";Hipt_curr
270
IF Flag THEN OUTPUT Load;"CAL:MEAS:HIGH";Hipt_curr
280
OUTPUT Load;"CURR";Curr_lopt
290
INPUT "Enter current through shunt for low point in amps",Lopt_curr
300
OUTPUT Load;"CAL:LEV:LOW";Lopt_curr
310
IF Flag THEN OUTPUT Load;"CAL:MEAS:LOW";Lopt_curr
320
PRINT "Test unit to verify that main (and readback) values are in spec"
330
PRINT "Press CONTINUE when ready to calibrate transient level"
340
PAUSE
350
OUTPUT Load;"CURR";Curr_lopt
360
OUTPUT Load;"TRAN:MODE TOGG"
370
OUTPUT Load;"TRIG:SOUR BUS"
380
OUTPUT Load;"TRAN ON"
390
OUTPUT Load;"CURR:TLEV";Curr_hipt
400
OUTPUT Load;"*TRG"
410
IF Flag THEN WAIT 30
420
INPUT "Enter current through shunt for transient point in amps",Trans_curr
430
OUTPUT Load;"CAL:TLEV";Trans_curr
440
OUTPUT Load;"TRAN OFF"
450
PRINT "Test unit to verify that transient values are in spec"
460
PRINT "Press CONTINUE when ready to calibrate next range or mode"
470
PAUSE
480
SUBEND
490
!
500
SUB Cal_volt(Load,Chan,Volt_hipt,Volt_lopt)
Содержание 6050A
