Agilent Technologies 11713A Скачать руководство пользователя страница 63

Страница: 63 / 88

11713 Operating and Service Manual 7-13

Replacing Major Assemblies

A6 Interface Assembly Removal/Replacement

CAUTION

This module contains components that can be damaged or destroyed by
electrostatic discharge. It should be serviced at a static-safe
workstation. Refer to "Preparing a Static-Safe Work Station" in
Chapter 8.

To Remove the A6 Interface Assembly

1. Remove both covers. Unscrew one screw on each cover and then slide

the cover toward the rear.

2. Disconnect the ribbon cable from the A1 interconnect assembly to

the rear panel.

3. Remove the rear panel from the main frame by removing the four

corner screws.

4. Remove the three screws that secure the A6 interface assembly.

To Replace the A6 Interface Assembly

1. Use the three screws to install the A6 interface assembly to the rear

panel.

2. Assemble the rear panel to the main frame using the four corner

screws.

3. Connect the ribbon cable from the rear panel to the A1 interconnect

assembly.

4. Replace the module covers.

Содержание 11713A

























































































Результаты поиска

Содержание 11713A

Отзывы:

Похожие инструкции для 11713A

Бренды по названию

Популярные бренды

Agilent Technologies 11713A, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 11713A

Отзывы:

Похожие инструкции для 11713A

Бренды по названию

Популярные бренды