AGI MK/HX 10-36 Скачать руководство пользователя страница 43

Страница: 43 / 54

30549 R1

6. Operation

The MK/HX 10–36 auger requires that operators follow the checklist before each start-up and that
safety procedures are observed at all times. To do otherwise is endangering life and limb, and is a
misuse of the equipment.

• Keep all children and unauthorized peronnel clear of work area.

• Do not operate auger with any safety shields removed.

• Do not operate auger with any service, clean-out or access door open or unlatched

or with safety discharge door open.

• Always have another person nearby to shut down auger in case of accident.

• Wear hearing protection during operation.

• Keep body, hair and clothing away from any moving parts.

• Shut down and lock out all power before servicing, cleaning, or adjusting auger.

6.1. Pre-Operational Checklist

Before operating auger for the first time, and each time thereafter, the operator must follow the checklist,
which should confirm the following:

• All fasteners are secured as per assembly instructions.

• Lift cable is not frayed or damaged.

• Lift cable is properly seated in track roller.

• Cable clamps are secure.

• PTO driveline is connected and secure.

• PTO driveline shield rotates freely.

• Clean-out and service doors and access covers are in place and secure and safety discharge door is closed.

• All safety shields are in place and secure.

• Tube alignment is reasonably straight.

• Intake hopper and discharge spout are free of obstructions.

• Auger wheels are chocked and tractor wheels are chocked or parking brake is applied.

• A second qualified person is present during operation.

• Operators are aware of safety precautions.

• Proper maintenance is performed.

• Tractor and auger are in line or as close to being in line as possible.

MK/HX 10-36 – SWING-AWAY GRAIN AUGER

6. OPERATION

Содержание MK/HX 10-36























































Результаты поиска

Содержание MK/HX 10-36

Отзывы:

Бренды по названию

Популярные бренды

AGI MK/HX 10-36, Руководство по сборке и эксплуатации

Результаты поиска

Содержание MK/HX 10-36

Отзывы:

Бренды по названию

Популярные бренды