manualshive.com logo in svg

AGI MK/HX 10-36, Руководство по сборке и эксплуатации

Поделиться
Скачать
AGI MK/HX 10-36 Скачать руководство пользователя страница 38

38

30549 R1

4. Transport

The MK/HX 10-36 Grain Auger is designed to be transported and/or operated without unhitching unit
from tractor. We strongly advise that all safety precautions be observed before transporting auger.

• Keep children and all unauthorized personnel away.

• Attach a SMV sign before transporting auger on a public road.

• Do not tow faster than 15 MPH (24 km/h).

• Use extreme caution in turning and cornering.

• Do not tow auger on slopes greater than 20 degrees.

• Do not allow persons to ride on the auger when it is being transported.

• Always tow auger in the lowered position.

• Disconnect PTO driveline from tractor for transport and placement.

4.1. Pre-Transport Checklist

Before transporting auger, ensure that:

1. Auger is in full-down position with PTO driveline disconnected from tractor. The roller trackshoe should be

seated against the upper trackstop with slight tension on the lift cable.

Important

Winch must be in locked position. To lock, turn handle clockwise until two clicks are heard. Check lift
cable before each use. Replace if frayed or damaged.

2. Make certain that the hitch pin and safety chain are in place and secure. Place safety chain through clevis

welded to auger hitch tube and bolt together before attaching to tractor (see

Figure 39

).

Figure 39.

3. Ensure that the intake feed hopper is raised into transport position and secured with hopper lock in place

with saddle pins and hairpins (see

Figure 40

and

Figure 29 on page 31

). DO NOT OPERATE AUGER WITH

INTAKE HOPPER IN TRANSPORT POSITION. THIS WILL DAMAGE THE U-JOINT.

4. TRANSPORT

MK/HX 10-36 – SWING-AWAY GRAIN AUGER

Содержание MK/HX 10-36























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды