AGI MK/HX 10-36 Скачать руководство пользователя страница 11

Страница: 11 / 54

30549 R1

Table 1.

Safety Decals

Part Number

Description

20813

To prevent death or serious injury:

• KEEP AWAY from rotating auger flighting.
• DO NOT remove or modify auger flighting

guards, doors, or covers. Keep in good working

order. Have replaced if damaged.

• DO NOT operate the auger without all guards,

doors, and covers in place.

• NEVER touch the auger flighting. Use a stick or

other tool to remove an obstruction or clean out.

• Shut off and lock out power to adjust, service, or

clean.

ROTATING FLIGHTING HAZARD

DANGER

20818

DANGER

To prevent serious injury or death:

• Keep body, hair, and clothing away from rotating

PTO driveline.

• Do not operate equipment unless all driveline,

tractor, and equipment shields are in place and in

good working order.

• Make certain the driveline shields turn freely on

driveline.

• Make certain the driveline is securely attached at

both ends.

• Do not exceed specified operating speed (see

operator’s manual).

• Keep u-joint angles small and equal. Do not exceed

maximum recommended length for PTO driveline.

ROTATING PTO DRIVELINE

MK/HX 10-36 – SWING-AWAY GRAIN AUGER

2. SAFETY FIRST

Содержание MK/HX 10-36























































Результаты поиска

Содержание MK/HX 10-36

Отзывы:

Бренды по названию

Популярные бренды

AGI MK/HX 10-36, Руководство по сборке и эксплуатации

Результаты поиска

Содержание MK/HX 10-36

Отзывы:

Бренды по названию

Популярные бренды