AGF COLLECTanDRAIN 5400 Скачать руководство пользователя страница 7

AGF Manufacturing Inc. • Phone: 610-240-4900 • Fax: 610-240-4906 • www.testandrain.com

7

OPERATING INSTRUCTIONS

The M5400 is equipped with a 150W heater controlled by a user-set thermostat. 
The factory default setting of 50º F is suitable for conditions down to 0º F. Consult 
with AGF for recommended settings if operating the M5400 in areas below 0º F. 
The thermostat controls the heater operation to within approximately ± 10º F of 
the set-point (i.e. Set-Point=50º F: ON @ 40º F—OFF @ 60º F).
NOTE: AGF does not recommend setting the thermostat below 50º F.
Power  Consumption  of  the  M5400  is  based  on  a  number  of  factors  including 
ambient  temperature,  humidity,  installation  location  and  exposure  to  sunlight. 
The following graph shows an estimation of the daily energy consumption verses 
ambient temperature when the set-point is 50º F.

0.00

0.20

0.40

0.60

0.80

1.00

1.20

1.40

1.60

1.80

2.00

-20

-10

0

10

20

30

40

50

Po

wer 

(kWh

/d

ay)

 

Average Ambient Temperature (°F) 

Est. Daily Power Consumption 

Rotate the red Thermostat Set-Point Dial clockwise until the heater turns on.

5. 

NOTE: The alarm will sound about 2 seconds after the heater turns on.

Reset the red Thermostat Set-Point Dial to the factory default of 50°F and 

6. 

reset the top dial of the Timer to the 

10h

 band.

NOTE: The Top Dial is a maximum time setting and not the Timer’s delay setting. 
The  Middle  Dial  controls  the  exact  amount  of  delay  for  the  timer.  The  factory 
default is 2 hours.

See steps 6 and 7 under Model 5400A (pg 6).

7. 

The  M5400  features  a  thermometer  on  the  cabinet  for  measuring  the  ambient 
temperature inside the unit. This thermometer is for checking the operating status 
of the heater.
The M5400 also features a Float-Style Level Switch for monitoring the collected 
condensate. This switch is tied back to the integrated NEMA 4 Alarm Panel. When 
enough  condensate  has  accumulated,  the  Level  Switch  is  activated  triggering 
the alarm horn to sound and pulse the red light mounted on the M5400 alarm 
panel. The alarm horn and light indicates that the M5400 needs to be emptied. An 

Содержание COLLECTanDRAIN 5400













Отзывы: