manualshive.com logo in svg

AeroWorks STINGRAY ELECTRIC ARF, Инструкция по сборке

Поделиться
Скачать
AeroWorks STINGRAY ELECTRIC ARF Скачать руководство пользователя страница 24

 

29. Slide the left elevator onto the wire elevator 

connecting rod and the CA hinges.  Wipe away 
any excess epoxy with alcohol wipes.  Ensure 
there is no epoxy remaining anywhere between 
the trailing edge of the stab and the elevator. 

 
 
 
 

 

 
 
 
30. Slide the right elevator onto the wire elevator 

connecting rod and the CA hinges.  Wipe away 
any excess epoxy with alcohol wipes.  Ensure 
there is no epoxy remaining anywhere between 
the trailing edge of the stab and the elevator.  

 

 

 
 
 
 
 
 

31. Slide the elevators onto the stab making sure all 

hinges go into their slot.  Remove the T pins and 
press the elevator against the stab trailing edge.  
Allow enough hinge gap to ensure maximum 
control throws.  Place 3-4 drops of thin CA on 
each side of all hinges.  Do not over soak the CA 
hinges.  Glue may run out and cause binding 

 
 

 

 
 
 
32. Make a 90º bend 1/4” from the end of the wire 

elevator pushrod. 

 
 
 
 

 

 
 
 
 
 

24 

 

Содержание STINGRAY ELECTRIC ARF










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды