manualshive.com logo in svg

Aerovent IM-895, Инструкция по установке, эксплуатации и обслуживанию, Страница: 19 / 24

Поделиться
Скачать
Aerovent IM-895 Скачать руководство пользователя страница 19

Installation, Operation & Maintenance Manual

IM-895

19

IV.  Burner Inspection

1.  Spark Igniter Secured Properly: 

2.  Flame Rod Secured Properly:

3.  Ignition Wire Attached at Igniter and Transformer: 

4.  Unions Tight and Secure:

Comments:

V.  Gas Manifold & Vent Piping

1.  Manifold Assembly Components Tight and Securely Mounted:
2.  All Fittings and Components Tight and Securely Mounted:
Comments:

VI.  Electric Service

1. Electrical Service Provided to Unit: 

Volts 

 Phase 

 Hertz 

Amps

2. Unit Nameplate Electrical Requirements: 

Volts 

 Phase 

 Hertz 

Amps

3. Main Fusing Size (if applicable): 

Volts 

 Amps

4. Overload Relay Setting (if applicable): 

Amps

5.  Terminal Strip Wires Tight and Secure at:  Main Panel: 

Yes 

Remote Panel: 

Yes 

N/A

6. Componentry and Relays Mounted Securely in Place: 

Yes

7.  Unit has been grounded by installer at the main unit panel:   

Yes

Comments:

VII.  Gas Service

 (see maximum and minimum gas pressure requirements on unit rating plate)

Natural Gas 

LP Gas 

Service Pressure:   ________" w.c.   - or-   ________oz.   - or-   ________psig

Comments:

Содержание IM-895

























Отзывы:

Нет отзывов