Aerovent IM-895 Скачать руководство пользователя страница 18

Страница: 18 / 24

Installation, Operation & Maintenance Manual

IM-895

Customer:

Sales Representative:

Model Number:

Serial Number:

FIELD START-UP SHEET

Direct Gas-Fired Equipment

INITIAL INSPECTION

I. Installer Responsibilities

1. Remote Panel (all interconnecting wires run from remote to unit):

Yes

N/A

Temperature control interconnect wires to remote ran in:

Shielded Cable

Separate Conduit

Remote Panel Location: ______ feet from unit (approx.)

Inside Wall

Outside Wall

PLEASE NOTE: If the Remote to Main Panel Interconnect Wiring is over 200' Long, Please Consult Factory!!

2. Gas supply connected with proper gas pressure regulator, drip leg, etc.:

Yes

3. Electrical supply connected with proper voltage/amperage, as stated on nameplate:

Yes

4. All electrical connections on all components are tight, including motor connections:

Yes

5. All "shipped loose" items installed properly (door switch, temp sensor, temp dial and gas valve assembly):

Yes

Comments:

II. Miscellaneous Items

1. Visible Physical Damage:

Yes

Explain:

2. Hardware Tight and Secure:

Yes

3. Damper Linkage Secure:

Yes

N/A

Comments:

III. Fan & Motor

1.  Fan Secured Tightly to Motor Shaft:
2.  Bushing Bolts Secure:
3.  Motor Manufacturer:

HP:

FLA:

Frame Size:

Comments:

Содержание IM-895

























Результаты поиска

Содержание IM-895

Отзывы:

Aerovent IM-895, Инструкция по установке, эксплуатации и обслуживанию, Страница: 18 / 24

Результаты поиска

Содержание IM-895

Отзывы: