Aerotech HexGen HEX300-230HL Скачать руководство пользователя страница 8

Страница: 8 / 44

DANGER

: To decrease the risk of electrical shock, injury, death, and damage to the

equipment, obey the precautions that follow.

Electrical installation must be done by qualified personnel.

Before you do maintenance to the equipment, disconnect the electrical power.

Before you connect wires to this product, disconnect the electrical power.

Do not connect or disconnect electrical components, wires, and cables while this
product is connected to a power source.

Restrict access to the hexapod when it is connected to a power source.

Make sure that all components are grounded correctly and that they obey the local
electrical safety requirements.

Supply each operator with the necessary protection from live electrical circuits.

Install the necessary precautions to supply safety and protection to the operator.

It is the responsibilty of the system integrator or qualified installer to determine and
meet all safety and compliance requirements when they integrate the HEX300-230HL
into a completed system.

DANGER

PINCH POINT!

Keep Hands Clear while the stage is in motion.

WARNING

: To prevent damage to the equipment and decrease the risk of electrical

shock and injury, obey the precautions that follow.

Only trained operators should operate this equipment.

Use this product only in environments and operating conditions that are approved in
this manual.

Make sure that the product is securely mounted before you operate it.

All service and maintenance must be done by approved personnel.

WARNING

: Securely mount and position all system cables.

IMPORTANT

: Carefully lift, move, and transport this product.

Safety Procedures and Warnings

HEX300-230HL Hardware Manual

www.aerotech.com

Содержание HexGen HEX300-230HL













































Результаты поиска

Содержание HexGen HEX300-230HL

Отзывы:

Похожие инструкции для HexGen HEX300-230HL

Бренды по названию

Популярные бренды

Aerotech HexGen HEX300-230HL, Руководство по оборудованию

Результаты поиска

Содержание HexGen HEX300-230HL

Отзывы:

Похожие инструкции для HexGen HEX300-230HL

Бренды по названию

Популярные бренды