manualshive.com logo in svg

Aerotech Automation1 iXL2e, Руководство по оборудованию, Страница: 81 / 96

Поделиться
Скачать
Aerotech Automation1 iXL2e Скачать руководство пользователя страница 81

4.2. Joystick Interface

Aerotech Multi-Axis Joystick (NEMA12 (IP54) rated) is powered from 5 V and has a nominal 2.5 V

output in the center detent position. Three buttons are used to select axis pairs and speed ranges.

An optional interlock signal is used to indicate to the controller that the joystick is present. Joystick

control will not activate unless the joystick is in the center location. Third party devices can be used

provided they produce a symmetric output voltage within the range of -10 V to +10 V.
Connecting joystick with an Aerotech cable, all Aerotech cables are labeled to identify the connector

and connections. The joystick parameters must be set to match the analog and digital

I/O connections. Refer to the

Help file

for programming information about how to change joystick

parameters.

Figure 4-2:

Two Axis Joystick Interface

Hardware Manual

iXL2e/XL2e

www.aerotech.com

81

Содержание Automation1 iXL2e

































































































Отзывы:

Нет отзывов