Aerotech Automation1 iXL2e Скачать руководство пользователя страница 21

Страница: 21 / 96

1.1. Electrical Specifications

Table 1-2:

Linear Amplifier Specifications

XL2e

Motor

Supply

Input Voltage

±5 VDC to ±48 VDC

Input Current

(continuous)

5 A

Input Current

10 A

Control

Supply

Input Voltage

24 VDC

Input Current

2 A max, 0.75 A typical without brake

Output Voltage (maximum)

±48 VDC

Peak Output Current (1 second)

(1)

10 A

Continuous Output Current

(2, 3)

±48 Bus

±40 Bus

±24 Bus

±20 Bus

±12 Bus

Stationary AC or DC motor

1.3 A

1.6 A

2.7 A

3.3 A

5.0 A

AC motor that is in motion

1.7 A

2.2 A

3.8 A

4.5 A

5.0 A

Maximum Continuous Total

Power Dissipation

(3)

180 W

Peak Amplifier Power

Dissipation per phase

(4)

400 W

Effective Heatsink Thermal

Resistance

0.25°C/W

Maximum Transistor Temperature

75°C

Time to reach maximum

temperature at maximum

continuous power

8 minutes

Power Amplifier Bandwidth

2500 Hz maximum (software selectable)

Modes of operation

Brushless, Brush, Stepper

Protection Features

Peak current limit; Over temperature; RMS current limit;

Control power supply under voltage; Dynamic power limit

(SOA)

(1) This specification depends on the motor supply voltage, the motor speed, and motor resistance. Contact an Aerotech

sales engineer for more information.

(2) This specification assumes that an AC or DC motor type with a 0 Ω winding resistance is used.

(3) The specification will be lower when the ambient temperature exceeds 25°C.

(4) The amplifier will limit peak power to protect itself from damage. The Amplifier Status internal signal in the Data

Visualizer shows the current state of the power limiting circuitry.

Hardware Manual

iXL2e/XL2e

www.aerotech.com

Содержание Automation1 iXL2e

































































































Результаты поиска

Содержание Automation1 iXL2e

Отзывы:

Aerotech Automation1 iXL2e, Руководство по оборудованию, Страница: 21 / 96

Результаты поиска

Содержание Automation1 iXL2e

Отзывы: