Aerotech Automation1 iXL2e Скачать руководство пользователя страница 19

Страница: 19 / 96

Table 1-1:

Feature Summary

Standard Features

24 VDC control supply input (

Section 2.1.1.

)

±5 to ±48 VDC bipolar motor supply inputs (

Section 2.1.2.

)

Line driver square wave quadrature encoder input for position and velocity feedback (

Section

2.3.1.

)

Absolute Encoder support (

Section 2.3.1.2.

)

One fail-safe brake output (

Section 2.3.6.

)

Two STO sense inputs (

Section 2.4.

)

One 10/100/1000 BASE-T Ethernet Port (

iXL2e Only

)

One USB 2.0 Type C Port (

iXL2e Only

)

Options

Peak Current (

Section 1.1.

)

-10

10 A Peak, 5 A Continuous Current

Expansion Board (

Chapter 3

)

-EB0

No Expansion Board

-EB1

I/O Expansion Board

16-bit analog output (±10 V)

16-bit differential analog input (±10 V)

8 digital logic inputs (5 - 24 VDC), can be connected to current sourcing or sinking

devices

8 digital logic outputs (5 - 24 VDC), can be connected as current sourcing or

sinking

Digital logic laser firing (PSO) output

-EB2

Industrial Ethernet Expansion Board

(iXL2e only)

Digital logic laser firing (PSO) output

Auxiliary encoder input channel

Two 10/100/1000 BASE-T Industrial Ethernet Ports

PSO (

Section 3.1.

)

-PSO1

One-axis PSO firing (includes One-axis Part-Speed PSO)

-PSO2

Two-axis PSO firing (includes Two-axis Part-Speed PSO)

-PSO3

Three-axis PSO firing (includes Three-axis Part-Speed PSO)

-PSO5

Two-axis Part-Speed PSO firing, which uses the PSO firing circuit based off of the

commanded vector velocity of up to 2 axes (includes One-Axis PSO).

-PSO6

Three-axis Part-Speed PSO firing, which uses the PSO firing circuit based off of the

commanded vector velocity of 3 or more axes (includes One-Axis PSO).

NOTE: Requires -EB1 option to generate a PSO output pulse

Multiplier (

Section 2.3.1.3.

)

-MX0

No encoder multiplier

-MX2

Interpolation circuit allowing for analog sine wave input on the primary encoder

channel with an interpolation factor of 65,536.

-MX3

Interpolation circuit allowing for analog sine wave input on the primary encoder

channel with an interpolation factor of 65,536 and an auxiliary encoder channel with

an interpolation factor of 16,384.

Version

-DEFAULT

Firmware Matches Software Line

-LEGACY

Legacy Firmware Version X.XX.XXX

Hardware Manual

iXL2e/XL2e

www.aerotech.com

Содержание Automation1 iXL2e

































































































Результаты поиска

Содержание Automation1 iXL2e

Отзывы:

Aerotech Automation1 iXL2e, Руководство по оборудованию, Страница: 19 / 96

Результаты поиска

Содержание Automation1 iXL2e

Отзывы: