Aeroflex 8210A-2-5 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 56

Aeroflex 8210A-2-5 Скачать руководство пользователя страница 38

Model 8210A-2-5

IM-377

Aeroflex / Weinschel

38

IDN

Function:

Assigns system model, and serial number Syntax: IDN model serialno

Argument(s):

model

string10

system model

serialno

string10

system serial number

Remarks:

This function is used to set the system identification info. The assignment can be

stored in non-volatile memory via the SAVE IDN command, and will be recalled during system
initialization.

Return Value:

none

Example(s):

IDN ’8210A-2-5’ ’123’

CONFIG FORMAT HEX

Function:

Sets the output format used for hexadecimal numbers.

Syntax:

CONFIG FORMAT HEX

fmt

Argument(s):

fmt

integer

format type

Remarks:

This function is used to set the output formatting style used for hex numbers. By

default, the 8210A-2-5 uses the formatting prefix specified by IEEE 488.2, which uses a prefix of ’#H’
for hex numbers. If desired, this prefix may be changed to the C language style "0X" by specifying a
value of 0 for the

fmt

argument. Any other value results in the default IEEE 488.2 format.

Return Value:

none

Example(s):

CONFIG FORMAT HEX 0

CONFIG SERIAL EOS

Function:

Sets the output End Of String character sequence for RS232 operation

Syntax:

CONFIG SERIAL EOS

eoschars

Argument(s):

eos

word end of line sequence

Remarks:

This function is used to set the End Of String line-termination character(s) used

during RS232 operation. By default, the 8210A-2-5 uses the ASCII CR-LF sequence (0x0D, 0x0A)
when sending information. The

eos

parameter can be used to specify a new terminator. The upper-

byte of the

eos

word is sent first, followed by the low-byte. In either case, a value of 0 results in no

character being sent.

Return Value:

none

Example(s):

CONFIG SERIAL EOS 0x0D0A (CR followed by LF default)

CONFIG SERIAL EOS 0x0D (CR only)

CONFIG SERIAL EOS 0x0A (LF only)

CONFIG SERIAL EOS 0x1A (^Z End Of File marker)

CONFIG CMDSET

Function:

Sets the active command set

Syntax:

CONFIG CMDSET

name

Argument(s):

name

string

new command set name

Remarks:

This function is used to set the active command set. By default, the 8210A-2-5 uses

its native command set, as described in this manual. In order to switch command sets automatically,
the POWERON macro can be used to change the "default" command set. Consult the factory for
specific details.

Return Value:

none

7-19. Device Interface Bus Control Commands

DEVICE PROTOCOL

Function:

Sets the protocol for use by low-level DEVICE commands

Syntax:

DEVICE PROTOCOL

prottype

Argument(s):

prottype

string

protocol type

val id protocol types include:

BASE

ATTN

STEPATTN

SWITCH

Remarks:

This function is used to set the protocol selection for use by the various low-level

DEVICE commands. Each different device supports a number of device-dependent messages.

Return Value:

none

Example(s):

DEVICE PROTOCOL STEPATTN

«
...
36
37
38
39
40
...
»

Содержание 8210A-2-5

























































Отзывы:

Нет отзывов