manualshive.com logo in svg

Aeroflex 8210A-2-5, Руководство по эксплуатации и установке, Страница: 29 / 56

Поделиться
Скачать
Aeroflex 8210A-2-5 Скачать руководство пользователя страница 29

Model 8210A-2-5 

 

IM-377 

Aeroflex / Weinschel 

29

 

7-12. Attenuator 

Control 

ATTN  

Function:  

Set attenuation 

Syntax:

 

ATTN name  atten (specific form) or ATTN atten (non-specific form)  

Argument(s):

 

name 

 

string10  

attenuator or group name 

 

atten

  

real  

desired value, in dB  

Remarks: 

 

This function sets the attenuation of  attenuator name to atten. This command may be 

used with both physical and virtual attenuation devices supporting the AttnProtocol. The parameter 
name must have been previously assigned using either the ASSIGN, ASSIGN ATTN, or GROUP 
command.  The non-specific form of this command will set all attenuation devices found during the 
configuration process to the value atten. It may be used to initialize the system, or as an easy method of 
programming systems that contain a single attenuator.  Also, this form allows the value of atten to be 
specified as -1, which results in each device being programmed to it’s maximum attenuation value. If 
name is a group name, then the command is performed on each attenuator of the group.  

Return Value: 

 none 

 

Example(s): 

 

ATTN AT1  63 

 

ATTN  ChanTwo  12.25  

 

ATTN  45.0 

ATTN?  

Function:

 Read 

attenuation 

Syntax:

 

ATTN? name (specific form) or ATTN? (non-specific form) 

Argument(s): 

 

name

  

string10  

attenuator name  

Remarks: 

 

In the specific form, this function reads the attenuation of  attenuator name. This 

command may be used with both physical and virtual attenuation devices supporting the AttnProtocol. 
The parameter name must have been previously assigned using either the ASSIGN or ASSIGN ATTN 
command. The non-specific form may be used in systems where there is only a single attenuator.  

Return Value:

  

atten

  

real  

attenuation value, in dB  

Example(s)

:  

ATTN?  AT1 returns ’63.00’ 

REF  

Function:

  

Sets reference attenuation  

Syntax: 

 REF 

name 

 

Argument(s):

  

name

  

string10  

attenuator or group name  

Remarks:

  

This function is used to set the reference level of the attenuator specified by name to 

the device’s current setting. This command may be used with both physical and virtual attenuation 
devices supporting the AttnProtocol. The parameter name must have been previously assigned using 
either the ASSIGN, ASSIGN ATTN, or GROUP command. The reference attenuation is used by the 
RELATTN command to program an attenuation relative to a reference value. If name is a group name, 
then the command is performed on each attenuator of the group.  

Return Value:

   none  

Example(s): 

 

REF AT1 sets reference level for AT1 to the current setting 

REF?  

Function:

  

Read reference setting  

Syntax:

  

REF? 

name

  

Argument(s): 

 

name

  

string10  

attenuator name  

Remarks:

  

This function reads the reference setting  of  attenuator name. This command may be 

used with both physical and virtual attenuation devices supporting the AttnProtocol. The parameter 
name must have been previously assigned using either the ASSIGN or ASSIGN ATTN command.  

Return Value:

  

refatten

  

real  

reference attenuation value, in dB  

Example(s):

  

REF?  AT1 returns ’30.00’  

RELATTN  

Function: 

 

Sets attenuation relative to a reference setting  

Syntax: 

 RELATTN 

name  atten

  

Argument(s):

  

name

  

string10  

attenuator or group name 

 

atten

  

real  

desired value, in dB  

Remarks: 

 

This function sets the attenuation of  attenuator name to atten, relative to the 

reference value set by the REF command. This command may be used with both physical and virtual 
attenuation devices supporting the AttnProtocol. The parameter name must have been previously 
assigned using either the ASSIGN, ASSIGN ATTN, or GROUP command. If name is a group name, 
then the command is performed on each attenuator of the group.  

Return Value: 

 none 

 

Example(s):

  

RELATTN  AT1 10  increases the atten setting of  AT1 10dB from reference setting 

 

RELATTN  AT1 -10 decreases the atten setting of  AT1 by 10dB from the reference  

 setting 

Содержание 8210A-2-5

























































Отзывы:

Нет отзывов