background image

 

48 

9.1.2.5.3. 

NMEA Checksum „CS“ 

The checksum „CS“ will be displayed as 2-character-hexadecimal value. It is calculated as a XOR op-

eration of all signs of the data set between “$” and “*”. This means “$” and “*” will not enter into the cal-

culation. 

<CR>...carriage return (hex0D), 

<LF>... linefeed (hex 0A) 

9.2.  Protocol rain[e] 

The rain[e] uses in connection with the met[LOG] two protocols: 

 

Talker-Protocol 

 

SDI-12 on RS485 

9.2.1.  Talker-Protocol rain[e] 

Is the talker-protocol activated the rain[e] sends via the RS485 interface an ASCII-string in a with the 

rain[e] commander adjustable time interval between 10 and 60 s (standard setting=10 seconds) (see 

also rain[e] manual).  

 

In the sent ASCII-string are located the measuring values: 

 

Intensity in mm/min 

 

Total quantity in mm 

 

Status of the heating (1 = ON, 0 = OFF) 

 

Internal housing temperature in °C 

 

System status 

9.2.2.  SDI-12 on RS485 – rain[e] 

Alternatively, the communication with the rain[e] can take place via SDI-12 commands. The communi-

cation with the help of the SDI-12 protocol takes place deviating from the „SDI-12 A Serial- Digital In-

terface Standard for Microprocessor-Based Sensors, Version 1.3, 2012“ via the  RS485-interface. 

With this protocol the following measuring values and data can be called of via the met[LOG]:  

  Precipitation intensity of the last-minute mm/min 

  Precipitation amount since the last call off mm/m² 

  Temperature interior °C 

  Heating ON (1) / OFF (0) 

  Total heating capacity % 

  Error states: 

o

  Error exceedance of 10 °C at heating ON 

0 or 1 

o

  Error heating   

 

 

 

0 or 1 

o

  Error temperature sensors in the interior  

0 or 1 

o

  Error temperature sensor at the funnel   

0 or 1 

9.3.  Analogue Sensors 

For the connection of the analogue sensors are 4 analogue inputs available. The input can measure 

0…10 V with 12 bit (16bit ADU). Additionally, the input can be used as digital input. Basically, it is pos-

sible to connect the sensors with an active status signal (voltage). It is also possible to connect sen-

sors with an open collector (OC) or a switch contact (relay) for which, depending on the configuration, 

the supply voltage can be switched as a “switching voltage” on the digital inputs. 

Moreover, the met[LOG] has got the possibility to measure temperatures with the help of a NTC.  

9.3.1.  Sensors with voltage output 

The sensors with voltage output will be measured and stored according to their scaling. 

9.3.2.  Sensors with a status output 

Sensors with a status output can be e.g. a rain detector (rain yes/no) or a sunshine duration sensor 

(sun yes/no). 

Normally the sensors deliver the status as an OC, a switch contact and/or as an active voltage signal 

(e.g. no (0) = 0 V and yes (1) = 5 V) (the thresholds can be configured correspondingly).  

Содержание LAMBECHT METEO 00.95800.010000





























































Отзывы: