AEG Protect A. 1000 Скачать руководство пользователя | Manualshive

Страница: 20 / 36

background image

20

5

Installation and Operation

5.1

Check

Remove the UPS from its transport packaging and check that
it has not been damaged in transit. If you find any damage,
pack the unit up again and send it back to where you
purchased it.

5.2

Installation

Install the UPS unit in a protected location where there is an
adequate air supply and where it will be largely free from dust
build-up, corrosive vapours and electrically conductive
contamination.

Do not operate your UPS where it is exposed to high ambient
temperatures or atmospheric humidity. Set up the UPS at
least 20 cm away from the monitor in order to avoid
interference.

«
...
18
19
20
21
22
...
»

Содержание Protect A. 1000





































Отзывы:

Нет отзывов

Похожие инструкции для Protect A. 1000

UPS Edition One 1kVA

Бренд: a-TroniX Страницы: 32

Бренд: Alpha Technologies Страницы: 79

TRI POWER X33 MOD HP 10 kVA

Бренд: Alpha Technologies Страницы: 80

Бренд: Advanced Power Systems Страницы: 2

Бренд: SmartPower Страницы: 13

Бренд: Xtreme Power Conversion Страницы: 96

Бренд: LESTAR Страницы: 2

Бренд: ZGR Страницы: 52

Бренд: Eaton Страницы: 19

Бренд: Lenovo Страницы: 3

Бренд: Lenovo Страницы: 18

PowerScale CABINET A

Бренд: ABB Страницы: 101

Бренд: GE Страницы: 16

Бренд: DuraComm Страницы: 3

FLP-10-POPC-5-R-4Y-2Y

Бренд: Staco Energy Страницы: 20

Бренд: Tripp Lite Страницы: 16

Бренд: SonicWALL Страницы: 60

Бренд: Marathon Power Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды