Advanced Radiant Systems VA Range Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 44

background image

Page 23

Modulating Unitary Range

VA-LT206_11292016al

2" MIN.

DECORATIVE-GRILLE

PANEL

T-BAR SUSPENDED

CEILING

REFLECTOR SHIELD

(CUT TO FIT DECORATIVE-GRILLE)

NOTCH REFLECTOR SHIELD

AS REQUIRED FOR HANGERS

AND REFLECTOR SUPPORTS

T-BAR

SHIELD

INSTALL END CAP AS PER

"INSTALLATION OF END CAP"

NOTE:

CLOSE ALL CHAIN LINKS "S" HOOKS, "J" BOLTS AND TURNBUCKLES OR ANY OPEN CONNECTION.

Decorative Grille (Optional)

INSTALLATION

ES/ESH Range heaters are approved for the addition of Decorative Grille either directly to the heater reflector or

as part of a T-Bar installation where the heater is above the ceiling structure. Refer to Figure 23 and Figure 24

below for details.

DECORATIVE-GRILLE PANEL

REFLECTOR

NOTCH

DECORATIVE-GRILL SUPPORT

FOR HANGERS

& SUPPORTS

DECORATIVE-GRILLE SUPPORT

INSTALL FROM OUTSIDE OF SHIELD AND

HOLD WITH SCREWS FROM OUTSIDE

DECORATIVE-GRILLE CROSS STRAP

FASTEN WITH SCREWS

AT EVERY 5FT SECTION

NOTE:

CLOSE ALL CHAIN LINKS "S" HOOKS, "J" BOLTS AND TURNBUCKLES OR ANY OPEN CONNECTION.

INSTALL END CAP

AS USUAL

DECORATIVE-GRILLE

END ANGLE

FASTEN TO END CAP & DECORATIVE-GRILLE

SUPPORTS

Figure 23: Decorative Grille and Heater Installation

Figure 24: Decorative Grille and Heater Installation

«
...
25
26
27
28
29
...
»

Содержание VA Range













































Отзывы:

Нет отзывов

Похожие инструкции для VA Range

Бренд: Zibro Страницы: 16

Бренд: Danfoss Страницы: 16

Бренд: ZETRON Страницы: 20

Бренд: Zephir Страницы: 14

Бренд: Lynx Страницы: 23

Бренд: Paloma Страницы: 24

Бренд: Bard Страницы: 42

Бренд: Zodiac Страницы: 16

Бренд: Waves Страницы: 24

Бренд: Vanguard Страницы: 24

Бренд: AUTOTERM Страницы: 18

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

TERRA SWM 3-13 HGL P

Бренд: iDM Страницы: 44

Бренд: golmar Страницы: 15

Бренд: LevelOne Страницы: 3

Бренд: RBI Страницы: 44

Бренд: Gasmate Страницы: 8

Бренд: Goodman Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды