Advanced Radiant Systems VA Range Скачать руководство пользователя страница 17

Страница: 17 / 44

Page 13

Modulating Unitary Range

VA-LT206_11292016al

INSTALLATION

Figure 9: Installation of First Section of Flanged Tube

Figure 10: Installation of Heat Exchanger Tube and Coupling

•

Place the first (flanged, aluminized) tube in the first two hangers (Figure 9). Be sure the flange is toward

the intended burner location. The other end of the tube should have the first coupling already loosely

fitted.

•

Always use all the hangers supplied. As a rule the combustion tube (first tube) utilizes 2 hangers and

thereafter 1 hanger per 10’ section. It is required that the first hanging point be 2” to 8” from the burner

mounting flange, and tube weld seam must face down, refer to Figure 9 for more details.

COUPLING SHOULD BE

LOOSELY FITTED

10'

8' - 9'

10'

LOCATE TUBE AND

REFLECTOR HANGERS

EVERY 10' THEREAFTER.

INSTALL "J" BOLT

AT FIRST HANGER

TUBE

FLANGE

TUBE WELD

SEAM FACING

DOWN

3"-5"

COMBUSTION

TUBE

CLOSE ALL OPEN ENDED

QUICK LINKS, CHAIN LINKS,

AND TURNBUCKLES OR ANY

OPEN CONNECTION.

TUBE & REFLECTOR

HANGERS

10'

COUPLING SHOULD BE

LOOSELY FITTED

HEAT

EXCHANGER

TUBE

TUBE WELD

SEAM FACING

DOWN

CLOSE ALL OPEN ENDED

"S" HOOKS, CHAIN LINKS,

AND TURNBUCKLES OR ANY

OPEN CONNECTION.

•

For all remaining tubes, fit the end of the tube with a coupling. The coupling should be loose (Figure 10).

Tube Installation

Содержание VA Range













































Результаты поиска

Содержание VA Range

Отзывы:

Похожие инструкции для VA Range

Бренды по названию

Популярные бренды

Advanced Radiant Systems VA Range, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание VA Range

Отзывы:

Похожие инструкции для VA Range

Бренды по названию

Популярные бренды