Adtec RD-71 Скачать руководство пользователя страница 69

Страница: 69 / 118

waveform teletext on CVBS and SD-SDI, set CVBS to line 22. When set to 0 waveform
teletext is disabled. To enable ancillary digital OP47 teletext on SDI or SDIALT, select a line
number next for the desired output.

VITC

- Not supported at this time (2.01.XX)

AFD

AFD is only supported on SDI and SDIALT via SMPTE 2016.

Timecode Configuration

- Not supported at this time (2.01.XX)

SMPTE 2038

The Adtec decoder supports Transport Stream to SDI ancillary data

pass-through via SMPTE 2038.

VBI Stats

shows the DID/SDID and data count for the SDI outputs if captions or AFD is

enabled. The AFD code can be seen in hex and the aspect ratio flag is also displayed.

Web UI - TS Output

ASI Tx

configures Service Filtering on the ASI Output. Read more in the

Service Filtering

section.

ASI Filter

ASI Filter enables or disables the configured RD service filter. Service Filtering

Содержание RD-71























































































































Результаты поиска

Содержание RD-71

Отзывы:

Бренды по названию

Популярные бренды

Adtec RD-71, Руководство пользователя

Результаты поиска

Содержание RD-71

Отзывы:

Бренды по названию

Популярные бренды