Adtec RD-71 Скачать руководство пользователя страница 54

Страница: 54 / 118

Client ID

is a unique identifier for this unit. It is called the remote ID on the Broadcaster.

Session ID

is the password for authentication to a Zixi Broadcaster. This is optional.

Latency

is the time given for error correction. It is recommended that latency is set higher

than 3 x Round trip time.

FEC Enabled

turns on or off Forward Error Correction. Note that FEC uses additional

bandwidth set by the Overhead.

FEC Content

aware allocates the FEC packets based on content.

FEC Overhead

is amount of FEC packets to use. This number is the percentage of your

overall bitrate. For example if set to 20%, then a 5Mb stream will use 6Mb of bandwidth as
1Mb will be used for FEC.

FEC Block

is the maximum time given to the FEC to correct an issue. This should not be

higher than half of the Latency setting.

Zixi Receiver IP Statistics

Data Bitrate

is the currently used IP rate, this can fluctuate depending on configuration

and environment.

Round trip time

measures how long a packet takes to travel to the broadcaster or encoder

and back. This calculation is important when configuring latency and determining error
correction configurations for the application.

Total Packets

are how many packets have been received since the IRD started receiving.

Jitter

is the variation in the delay of received packets. Larger jitter values could indicate

network congestion and increases the likelihood of network issues being seen.

Packet Rate

is the amount of network packets received per second.

Latency

shows what the latency is set to for the service.

Out of Order

shows how many packets have been received out of the sent order. This can

be caused by a high jitter or packets taking different routes through the network.

Overflow

shows the number of packets lost due to buffer overflow.

Dropped

shows how many packets have been lost since the receiver first locked to the

service.

Duplicates

shows how many packets have been repeated.

Recovered Packets

shows how many successful recoveries have occurred out of the total

Содержание RD-71























































































































Результаты поиска

Содержание RD-71

Отзывы:

Бренды по названию

Популярные бренды

Adtec RD-71, Руководство пользователя

Результаты поиска

Содержание RD-71

Отзывы:

Бренды по названию

Популярные бренды