manualshive.com logo in svg

Adtec RD-71, Руководство пользователя

Поделиться
Скачать
Adtec RD-71 Скачать руководство пользователя страница 51

 

descrambling. 0 is default. 

 
LNB State

​

 - 

​

This configuration will enable or disable power on the input connector to power 

the LNB. If on, the user can select the voltage and tone placed on the connector via the 
Polarity and Tone configurations.

 

 
LNB Polarity

​

 - 

​

This control is primarily used in “Universal” LNB applications. The LNB 

Polarity control allows for LNB polarization selection; the 13VDC source will select the 
Vertical polarity and the 18VDC source will select the horizontal polarity. For typical “C” and 
“Ku” band applications, the 18 VDC option is recommended.

 

 
Tone

​

 - 

​

This control is used only for Universal LNB applications. A universal LNB can route 

the high or low band from either polarity to the IRD. The high band is selected by enabling 
the 22 kHz tone and the low band is selected when the 0 Hz tone is enabled.

 

 
IP Params 
IP Params allow a user to configure IP Receive parameters and see detailed IP statistics.  
 

 

51

 

Содержание RD-71























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды