ADPRO ADPRO FastTrace Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 146

ADPRO ADPRO FastTrace Скачать руководство пользователя страница 99

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

87

Control Output Settings

When the

Configure

button is used, the following settings can be made.

Control Output Name

Option:

16 characters maximum.

Enter the 16 character name to associate with this output. The name can be displayed when
viewing video from a camera input associated with this control output.

Default State

Option:

Normally Open, Normally Closed

Default:

Normally Open

Defines the state of the control output when it is not being driven by an alarm condition or
controlled remotely.

When set for ‘normally closed’, the control output is shorted to ground via the output transistor.

Manual Operation

The control outputs can either be operated by an operator at VideoCentral or linked to an alarm
condition. Select this box if the VideoCentral operator is to control the output.

Note that this option must be set to allow remote users access to the control output function.

Disconnect Operation

Option:

Reset, Latch

Default:

Reset

Defines the operational state of the control output after a user has disconnected from the
FastTrace.

•

the

Reset

option returns the output to the condition defined by the

Default State

.

•

the

Latch

option causes the control output to remain in its current (operated) condition.

4.3.16 Audio

The

Audio

menu configures the FastTrace audio channel features.

FastTrace supports combined video and audio operation over communication links that have a
minimum data throughput of 14.4 kbps. This provides simultaneous video and audio operation,
with an audio bandwidth of 300 Hz-3 kHz, over standard public switched telephone networks
(PSTN) as well as high speed digital networks.

Note:

Although FastTrace always passes audio at the maximum possible bandwidth, the
overall audio quality will ultimately depend on the quality of the microphones and
speakers connected to the FastTrace and the level of background noise in the
environment. Tests should always be performed with the desired audio equipment
to obtain an understanding of the audio performance.

«
...
97
98
99
100
101
...
»

Содержание ADPRO FastTrace



















































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды