manualshive.com logo in svg

ADPRO ADPRO FastTrace, Инструкция по установке и эксплуатации

Поделиться
Скачать
ADPRO ADPRO FastTrace Скачать руководство пользователя страница 87

ADPRO FastTrace by Xtralis

Installation and User Manual

Doc 11168_12

75

Caution: 

Camera termination is only active whilst the FastTrace is powered. If, for any 
reason, the power is removed from a FastTrace unit, any connected cameras will 
become unterminated.

Use Activity Detection

The FastTrace can be setup to respond to changes that occur within the field of view of a 
camera. This feature is used to trigger an alarm if activity is detected by a certain camera in an 
area not normally expected to have activity.

To help configure the Activity Detection feature, the sensitivity to movement and the amount of 
time that movement occurs can be programmed. This is done by selecting the 

Activity 

Detection

 tab.

PTZ Settings

This Camera has a PTZ station.

Options:

Yes, No

Default:

 No 

Set the checkbox when this channel is connected to a camera with PTZ (Pan/Tilt/Zoom). The 
type of PTZ equipment is set in the 

PTZ Settings

 option (refer to “

PTZ Settings

” on page 72).

If checked, the 

Configure

 button will become available. By clicking on the 

Configure

 button, the 

Alarm Preset Settings may be modified.

Figure 73: Camera Settings - PTZ

The PTZ Preset on Alarm feature allows the user to associate an alarm input, activity detection 
on another connected camera or an ATM/EPOS transaction, to a preset camera position, so that, 
in the event of an alarm, FastTrace will send the PTZ camera to a pre-programmed preset 
position automatically. 

The following parameters must be defined to use the PTZ preset on alarm feature: 

•

Time delay between QUAD images

•

Alarm Preset Interrupt

•

Time delay between Alarm Presets

•

Enable Auto-Home

•

Auto-Home expiry time

Time delay between QUAD images is described in the section above - refer to “

QUAD Images 

Interval

” on page 74.

Содержание ADPRO FastTrace



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды