manualshive.com logo in svg

ADPRO ADPRO FastTrace, Инструкция по установке и эксплуатации

Поделиться
Скачать
ADPRO ADPRO FastTrace Скачать руководство пользователя страница 36

Installation and User Manual

ADPRO FastTrace by Xtralis

24

Doc 11168_12

Figure 29: Configure a New Site

2.

Enter the following site details:
-

Site Id

: 9 characters (max)

-

CMS Password

: 8 characters (max)

-

Communications

: Network or PSTN

3.

If Network is selected, enter a valid IP address for the FastTrace

4.

Click 

OK

. The configure Site dialog box is shown again. Click 

Close

. The System 

Administration options are then shown. Click 

Exit

.

If a Network connection is being used, the PC must now have its IP Address changed to be on 
the same subnet mask as the modified IP Address of the FastTrace (but with a different IP 
address). Refer to 

Configuring the PC for Ethernet Connection

 on page 9 for details of how to 

perform this.

2.11 Testing the FastTrace Installation

1.

Reconnect to the site by selecting the 

Connect to site

 button, highlighting the new site and 

press 

OK

.

2.

Test the operation of all connected cameras by selecting each camera in turn from the drop 
down list on the user interface.

Figure 30: Camera List

3.

While still connected to the site, test the operation of all programmed alarms by triggering 
them in turn and ensuring that the appropriate alert is sent to VideoCentral.

4.

Once operation is confirmed onsite, test the connection and operation at the CMS (if 
required). Connect to the CMS by triggering an alarm at the site, and ensure that the CMS 
can initiate connection to the site.

Содержание ADPRO FastTrace



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды