manualshive.com logo in svg

ADPRO ADPRO FastTrace, Инструкция по установке и эксплуатации

Поделиться
Скачать
ADPRO ADPRO FastTrace Скачать руководство пользователя страница 92

Installation and User Manual

ADPRO FastTrace by Xtralis

80

Doc 11168_12

Note: 

A Transaction Device Software License must be purchased to enable transaction 
device functionality. Licensing instructions are provided with the purchase of a 
licence (refer to 

Licensing

 on page 59).

A Transaction Device (for example an ATM or EPOS terminal) can be connected to the 
FastTrace via one of the GP Serial ports or Ethernet port. Up to sixteen transaction devices can 
be configured.

Note: 

Please contact your nearest Xtralis office for details of supported equipment.

For information on how to set up a transaction device, please refer to the Transaction Device 
Software Programmers Manual (document number 11620_01) available on the website - 

www.xtralis.com/adpro

.

4.3.12 Transparent Data Port

FastTrace supports transparent RS232 data transmission to/from VideoCentral. The port labelled 
DATA on the rear of the unit is the port used for this connection. This functionality provides the 
capability to transfer an RS232 data stream from the FastTrace unit to VideoCentral, and vice-
versa. This type of capability may be useful to support a camera station that is not listed in the 
supported list for FastTrace, or controlling some other industrial equipment at the remote site.

If a VideoCentral user connects to a FastTrace with transparent data enabled, the serial port is 
reserved exclusively for use by that user. Until that user disconnects, no other user can access 
transparent data.

Figure 78: Transparent Data Port Menu

To enable the Transparent Data Port check the Transparent Data Port Connected option.

Note: 

VideoCentral also requires configuration changes for this functionality (

Database

 / 

Administration

 / 

Configure Transparent Data Port

).

Содержание ADPRO FastTrace



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды