manualshive.com logo in svg

ADPRO ADPRO FastTrace, Инструкция по установке и эксплуатации

Поделиться
Скачать
ADPRO ADPRO FastTrace Скачать руководство пользователя страница 32

Installation and User Manual

ADPRO FastTrace by Xtralis

20

Doc 11168_12

2.8.1 Powering Up the FastTrace

The green Power and the red Status LEDs on the front panel are lit as soon as power is applied 
to the unit.

The FastTrace is supplied with a universal input power supply which operates from 100-240V 
AC, 50-60Hz. There are no switches to change based upon your particular mains power voltage 
or frequency.

If the green LED fails to illuminate check that there is power available from the socket into which 
the FastTrace is connected.

The FastTrace will then automatically perform a series of self-test routines which check the 
microprocessor circuits. When power is first applied to the FastTrace unit, the red LED on the 
front of the unit will be on. After approximately 60 seconds, the red LED should start switching 
on, then off, every two seconds. This signifies that the unit has completed its internal checks and 
is now checking the integrity of the HDDs. Once the unit successfully completes the integrity 
check, the red LED will switch off, and remain off.

If at any time during operation, the red LED switches on and stays on, this signifies a fault with 
the unit and technical support is required.

If the red LED does not switch off and remain off, do the following:

1.

Unplug all of the connectors except the power and re-power the unit.

2.

If the red LED extinguishes, plug each connector back in and check that the red LED 
remains off. 

3.

If the red LED does not extinguish after 10 minutes, please contact ADPRO technical 
support.

If the red LED continues to flash for an extended period, this signifies that corruption has been 
found with the database and the unit is attempting to correct the fault.

2.9

Connecting to the FastTrace for the First Time

1.

Connect the PC to the FastTrace unit, via the ethernet or serial cable.

2.

Power the FastTrace up.

3.

Wait for the FastTrace to complete its start-up checks. The red status light will initially be 
ON, then will start flashing, then go OFF once the checks are complete. This can take up to 
two or three minutes from power on.

4.

Start VideoCentral Lite from the icon on the desktop, if not already running.

5.

From within VideoCentral Lite click the 

Connect to Site

 button.

6.

Select the site named 

FastTrace default site

 and then select the connectors type in the 

Connect Via

 list. Click 

OK

. You should see the Connection Status screen followed by a 

screen confirming connection.

Содержание ADPRO FastTrace



















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды