ADLINK Technology NeuronBot Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 77

ADLINK Technology NeuronBot Скачать руководство пользователя страница 55

NeuronBot

List of Figures

55

# for dashing and eloquent

ros2 run nav2_map_server map_saver -f <map_name>

or

# for foxy:

ros2 run nav2_map_server map_saver_cli -f <map_name>

9. Stop the Slam Toolbox by pressing

ctrl + c

in the Slam Toolbox session (Session 3).

5.4.3. Navigation

After getting a static map, running a SLAM package is not recommended due to its computational load. This
section describes how to use an AMCL package to locate the NeuronBot using a previously generated map and
existing laser scan. This will allow you to move the NeuronBot from one location to a specified destination.

Note:

Ensure that everything in the base driver has been launched before running SLAM.



Terminal 1,

Session 2:

1. Source the environment.

source /opt/ros/<YOUR_ROS2_DISTRO>/setup.bash

source ~/neuronbot2_ros2_ws/devel/

local_

setup.bash

2. Start the navigation procedure by executing the following command.

ros2 launch neuronbot2_nav bringup_launch.py map:=<full_path_to_your_map_name.yaml>

«
...
53
54
55
56
57
...
»

Содержание NeuronBot














































































Отзывы:

Нет отзывов