ADJ ILLUSION DOTZ 3.3 Скачать руководство пользователя

Страница: 3 / 24

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or fire, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 45 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a

marked change in performance.

Illusion Dotz 3.3

Safety Precautions

ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 4

• 3 Modes of DMX-512 Protocol Compatible (12 DMX Channel

Mode, 14 DMX Channel Mode, and 38 DMX Channel Mode)

• RDMX - Lets you set the DMX address from any DMX Controller

• 3 Operating Modes - Master/Slave; Stand Alone; Sound Active

• Kling-Net and Art-Net Compatible (Recommended control solu-

tions; Arkaos Media Master Express, Media Master Pro, and LED

Master software’s (sold separately).

• Internal Microphone

• 5 Dimmer Curve Settings

• Power Cord Daisy Chaining (See below)

• Edit and Save Scenes into the Memory

• 360˚/ 540˚ Pan Movement

• 270˚ Tilt Movement

• Digital Display for Address and Function Setting

Illusion Dotz 3.3

Features

ADJ Products, LLC - www.adj.com - Illusion Dotz 3.3 Instruction Manual Page 5

With this feature you can connect the fixtures to one another

using the PowerCON input and output sockets. The quantity

that can be connected is 4 fixtures maximum for 120V and 9 fix-

tures maximum for 240V. After the maximum fixtures has been

reached you will need to use a new power outlet. They must be

the same fixtures. DO NOT mix fixtures.

Illusion Dotz 3.3

Power Cord Daisy Chain

Содержание ILLUSION DOTZ 3.3

























Результаты поиска

Содержание ILLUSION DOTZ 3.3

Отзывы:

Похожие инструкции для ILLUSION DOTZ 3.3

Бренды по названию

Популярные бренды

ADJ ILLUSION DOTZ 3.3, Инструкция пользователя

Результаты поиска

Содержание ILLUSION DOTZ 3.3

Отзывы:

Похожие инструкции для ILLUSION DOTZ 3.3

Бренды по названию

Популярные бренды