manualshive.com logo in svg

Adisa ADI CD 375, Техническое руководство по установке, использованию и обслуживанию

Поделиться
Скачать
Adisa ADI CD 375 Скачать руководство пользователя страница 49

ADI CD boiler - Technical Manual 

 

    

 

49 

 

 

17.4 Gas supply 
 

The gas supply pressure, the gas flow and the dimensions of the gas connection, they all depend on the type of gas 
used, according to the boiler installed and to the current regulations. 
 
Gas connection: the installation company has to install a three-pieces coupling per boiler in order to facilitate the 
dismantling and the maintenance of every boiler. 
 
The boiler incorporates a small mesh. If the connecting pipe is not clean or has particles, the mesh will immediately 
block them, so the installation company will have to install a gas filter before the boiler gas connection.  
 
If the boilers gas pressure is higher than the maximum value indicated in this manual, it is necessary to install a gas 
pressure governor so that the inlet working pressure can be in accordance with the values required. 
 
It is advisable to install a flue gas header previous to the boilers that will operate as a gas inertial tank when the 
boilers start working.  
 
When different consumptions are simultaneously required, the dimensions of the gas pipes and of the gas 
connections must be calculated so that, when all the consumptions are demanded simultaneously, the inlet working 
gas pressure to each boiler will correspond to the values indicated in this manual (see table TECHNICAL DATA). 
 
 

17.4.1 Gas pressure higher than 45 mbar 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Units 

 

 

Boiler 

model 

Inertial 

volume (m3) 

1 

CD 70 

0.0065 

1 

CD 85 

0.0082 

1 

 CD 105 

0.0100 

1 

 CD 120 

0.0115 

1 

 CD 175 

0.0154 

1 

 CD 200 

0.0188 

1 

 CD 250 

0.0229 

1 

 CD 325 

0.0279 

1 

 CD 375 

0.0336 

1 

 CD 450 

0.0417 

1 

 CD 550 

0.0508 

1 

 CD 650 

0.0575 

1 

 CD 750 

0.0651 

1 

CD 850 

0.0761 

1 

CD 950 

0.0859 

2 

 CD 325 

0.0736 

2 

 CD 375 

0.0736 

2 

 CD 450 

0.0899 

2 

 CD 550 

0.1058 

2 

 CD 650 

0.1196 

2 

 CD 750 

0.1196 

2 

CD 850 

0.1522 

2 

CD 950 

0.1719 

3 

 CD 375 

0.1348 

3 

 CD 450 

0.1587 

3 

 CD 550 

0.1794 

3 

 CD 650 

0.2016 

3 

 CD 750 

0.2016 

3 

CD 850 

0.2283 

3 

CD 950 

0.2578 

A gas pressure governor must be installed to reduce 
pressure to a value in accordance with the table of 
paragraph “Technical data”. To select the type and its 
speed of opening/closing, consult the Technical 
Department of ADISA BY HITECSA. 
An inertial tank must be installed between the gas 
pressure governor and the boiler, acting as a gas 
inertial volume when the boiler starts up and as an 
absorber/compensating of the pressure rise produced 
by the closing of the gas pressure governor when the 
boiler stops (see diagrams below).  
Its volume will be at least equal to 1/1000 of the boilers 
maximum flow per hour.   
This inertial tank must be placed as close as possible 
to the boiler.

 

2

ESQUEMA VARIAS CALDERAS

4

5

3

1

ESQUEMA UNA CALDERA

DIAGRAM OF 1 BOILER 

DIAGRAM OF SEVERAL BOILERS 

1. BOILER
2. 

GAS INERTIAL TANK 

3. GAS 

FILTRE 

4. GAS 

GOVERNOR 

5. MANOMETER 

Содержание ADI CD 375













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды