background image

 

 

 

 

 

SYMBOLOGY MACHINE

 

 

Symbol 0/1 indicating the 

ON/OFF switch and its signal 

lamp. 

 

Symbol that indicates the 

position of the outlet plug 

of the solution tank. 

 

 

 

 

 

Symbol denoting the switch 

for the water opening and 

the signal lamp that the 

water is open. 

 

This symbol indicates that 

the tanks need  to be 

emptied before rotating the 

machine. 

 

 

 

 

 

Symbol denoting the signal 

lamp of the starting of the 

brush rotation. 

 

Indication of the maximum 

temperature of the 

detergent solution. It is 

placed near the charging 

hole of the solution tank. 

 

 

 

 

 

Symbol denoting the switch 

and the signal lamp of the 

suction motor.  

 

Symbol that indicates the 

flow adjuster of the 

detergent solution. 

 

 

 

 

 

Symbol denoting the charge 

level of the batteries. 

 

Symbol 

denoting the 

crossed bin. Indicates that 

at the end of its activity, the 

machine has to be disposed 

conforming to the laws in 

force. 

SYMBOLOGY HANDBOOK 

 

Symbol denoting the open 

book. 

Indicates that the operator 

has to read the manual 

before the use of the 

machine. 

 

Obligation symbol requiring 

the wear of protection 

glasses. 

 

 

 

 

 

Symbol denoting the open 

book. 

For the good functioning of 

the 

on-board battery 

recharger, read the manual 

of the constructor. 

 

Obligation symbol requiring 

the wear of protection 

gloves. 

 

 

 

 

 

Warning symbol.  

Read carefully the sections 

marked with this symbol, 

for the security of both the 

operator and the machine. 

 

Symbol preceding an 

information about the 

correct use of the machine. 

 

 

 

 

 

Obligation symbol, 

disconnect the installation 

from the batteries acting 

upon the connector before 

any operation on the 

machine. 

 

Symbol indicating 

operations to be carried out 

only by qualified personnel. 

 

 

Содержание baby

























Отзывы: