ADC ADView 2 Скачать руководство пользователя | Manualshive

Страница: 16 / 51

background image

93-9005-00

ADView 2 User Manual | 16

September 1, 2016

Wi-Fi radio connected (segments will be illuminated continuously)

AC power connected

Printer connected and powered on

Barcode scanner connected and powered on

Error Alert Symbol

WARNING

: User must take immediate action (see additional information in Section 12)

Battery Level Indicator

Battery symbol (all bars illuminated indicate a full charge)

Blood Pressure Measurement Mode Selection Icons

Manual Mode (for auscultatory readings)

Averaging Mode

Number of measurements taken in averaging mode

Maximum pressure setting for Manual Mode

Time before first measurement in minutes (Illuminates when Averaging Mode is selected)

Time between measurements in seconds (Illuminates when Averaging Mode is selected)

Blood Pressure Results (DIA and SYS)

DIA

and

mmHg

: Diastolic blood pressure

SYS

and

mmHg

: Systolic blood pressure

EMR Transmission Icons

EMR icon prompts the user to confirm whether or not to send measurement data as message to EMR

system. (Only shown if EMR connectivity has been set up via Configuration Application.)

Message icon (Indicates if EMR messaging is successful)

If successful, the icon will flash on and off with check mark.

If not successful, it will flash on and off with X.

Adult or Child Patient Selection

Press and hold toggle button for 4 seconds, until selection knob starts flashing. Release toggle button, and use the
selection knob to select the icon needed. Selected icon will blink after 1 second. Press the selection knob to confirm
the selection.

Adult BP Mode icon. This icon is illuminated when the Adult BP mode is selected. The ADView 2 will remain in the

selected patient mode until a new mode is set.

«
...
14
15
16
17
18
...
»

Содержание ADView 2




















































Отзывы:

Нет отзывов

Похожие инструкции для ADView 2

Бренд: Walimex Pro Страницы: 44

Бренд: Otto Bock Страницы: 72

Portable Vocal Booth Pro Studio Series

Бренд: EditorsKeys Страницы: 2

Calculite C6P38MHA

Бренд: Lightolier Страницы: 2

Бренд: Mac Medical Страницы: 12

Бренд: Intellinet Страницы: 2

Бренд: Tormach Страницы: 19

Бренд: Master Страницы: 22

Бренд: Karma Страницы: 12

Бренд: p-light Страницы: 28

Бренд: Cardin Elettronica Страницы: 56

Бренд: Launch Страницы: 15

Бренд: RayLight Страницы: 31

Бренд: PLUSLITE Страницы: 13

Бренд: Jolly Страницы: 22

Бренд: Fox Страницы: 20

Ultima Access BCUA-8626M

Бренд: Inspired by drive Страницы: 8

HAMMERTONE 5037 925 GYM

Бренд: York Fitness Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды