manualshive.com logo in svg

ADC ADView 2, Руководство пользователя

Новый ADC ADView 2 - это компактный и удобный монитор давления, включающий в себя большой ЖК-дисплей. Не забудьте загрузить бесплатное руководство пользователя с нашего сайта, чтобы узнать больше о функциях этого превосходного устройства.обязательно загрузите его с manualshive.com.

Поделиться
Скачать
background image

93-9005-00    

 

     ADView 2 User Manual | 20 

September 1, 2016 
 

After connecting the optional thermal printer (see Section 2 and Section 3), ensure that the green LED on the top of 
the printer is lit and unblinking before printing. 

 

      

Reset 

Print 

To print the information currently displayed on the ADView 2 screen, press the print button on the top of the printer 
(see diagram above).  

Saving Measurements 

With EMR Connectivity 

Technicians may have already connected the ADView 2 to your facility’s EMR system. If so, you can easily send 
measurements directly to the EMR.  

With the patient’s current measurements displayed on the screen, press the Memory button 

. The EMR icon 

and Check Mark icon 

will begin flashing.  

Press the Selection Knob to send the data to the EMR. If the measurements are delivered to the EMR successfully, 

you will see the EMR Message icon 

 and the Check Mark icon 

 blink four times.  

To store the displayed measurements in the device memory without sending to the EMR: 

Press the Memory Button

, 

While the EMR and Check Icons are flashing, turn the Selection Knob until the X icon 

 is displayed and then press 

the Selection Knob. The measurements will be saved to the device memory only. 

Without EMR Connectivity 

The ADView 2 does not have to be connected to an EMR system to save measurements. You can save them to the 
device’s own memory. With the patient’s current measurements displayed on the screen: 

Press the Memory button

.  

All of the measurement values on the screen, the Check icon

and the Memory icon

 will flash on and off 2 

times.  

The display will then return to a blank screen/shows null values, but the Check Mark icon

will flash 2 more times, 

this verifies the measurements are successfully stored to the device’s memory.  

Note: The ADView 2 does not autosave. The user must save the reading to memory after every reading.  

To view results stored in memory, press the Memory Button

 for more than four seconds. You will see the 

most recently saved measurements displayed on the screen, and can turn the Selection Knob counterclockwise to 
see older measurements and then clockwise to see newer measurements. 

 

Содержание ADView 2




















































Отзывы:

Нет отзывов

Похожие инструкции для ADView 2

DB Industries DELTA 2 User Instructions preview
DELTA 2
Бренд: DB Industries Страницы: 60
vc999 K5 Operating Manual preview
K5
Бренд: vc999 Страницы: 55
Salsbury Industries 3700 Series Manual preview
3700 Series
Бренд: Salsbury Industries Страницы: 4
Mangar International Leglifter User Instructions And Warranty preview
Leglifter
Бренд: Mangar International Страницы: 8
Malvern Instruments Zetasizer uV Manual preview
Zetasizer uV
Бренд: Malvern Instruments Страницы: 30
Quantum ELM Replacement Instructions Manual preview
ELM
Бренд: Quantum Страницы: 11
Quanser QNET User Manual preview
QNET
Бренд: Quanser Страницы: 21
Quanser 3 DOF Laboratory Manual preview
3 DOF
Бренд: Quanser Страницы: 18
Xaoc Devices JENA Operator'S Manual preview
JENA
Бренд: Xaoc Devices Страницы: 8
M-Audio Ozone User Manual preview
Ozone
Бренд: M-Audio Страницы: 48
M-Audio FireWire 410 Quick Start Manual preview
FireWire 410
Бренд: M-Audio Страницы: 19
M-Audio Fast Track Pro User Manual preview
Fast Track Pro
Бренд: M-Audio Страницы: 17
M-Audio MidAir User Manual preview
MidAir
Бренд: M-Audio Страницы: 18
M-Audio X-Session Guía De Inicio Rápido preview
X-Session
Бренд: M-Audio Страницы: 12
M-Audio X-Session User Manual preview
X-Session
Бренд: M-Audio Страницы: 20
Össur QUICK-ALIGN Vari-Flex Instructions For Use Manual preview
QUICK-ALIGN Vari-Flex
Бренд: Össur Страницы: 36
Össur Patriot Collar Instructions For Use preview
Patriot Collar
Бренд: Össur Страницы: 2
Össur Unloader One Instructions For Use Manual preview
Unloader One
Бренд: Össur Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды