ADB L-861SE Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 30

ADB L-861SE Скачать руководство пользователя страница 23

© ADB bvba All Rights Reserved

17

2.6 Troubleshooting

2.6.1 Action Table in the

Event of a System or

Component Malfunction

This section contains troubleshooting information. This information covers only the most
common problems that you may encounter. If you cannot solve the problem with the
information given here, contact your local ADB Airfield Solutions’ representative for help.

Table 6:

Product ERTE Troubleshooting Guide Table

Problem

Possible Cause

Corrective Action

Lamp not energizing

Defective lamp

Replace the lamp

Loose or broken contacts

Replace the lamp or light socket

Power supply failure

Replace the power supply

Fixture wires pinched

Replace/repair the wire

Defective isolation transformer

Replace the transformer

Lamp not turning on at
normal level

Isolation transformer secondary current
incorrect or wrong frequency type

Check for the proper transformer size and replace with
the correct transformer

Wrong fixture installed

Replace the fixture

Improper color

inner lens broken

Replace inner lens

inner lens not installed or wrong color

Short lamp life

Current too high (series circuit
applications)

Calibrate the CCR

Cracked lens or base assembly

Replace the broken assembly. Clean and reassemble the
light fixture.

Component Failure

Replace the failed component. Check for a cause of the
failure and repair or replace any defective components.

«
...
21
22
23
24
25
...
»

Содержание L-861SE































Отзывы:

Нет отзывов