manualshive.com logo in svg

ADB L-861SE, Инструкция по эксплуатации, Страница: 22 / 30

Поделиться
Скачать
ADB L-861SE Скачать руководство пользователя страница 22

L-861SE Clamp Band ERTE
96A0193 Rev. i
    
Maintenance 

© ADB bvba All Rights Reserved

16

2.5.2 Maintenance 

Procedures

This section provides instructions for replacing lamps for the L-861SE threshold/end light 
fixture.

To replace a lamp, perform the following procedure:

1. See Figure 5. Remove the outer globe (H2) from the fixture by loosening the clamp band 

holding the lens to the base.

2. Remove the two inner lens segments (H1R/L) by pulling and sliding off the inner spring 

clip (H3) and the Inner Lens Clip (C1).

3. Pull the lamp (L1) from the socket (S1).
4. Wearing clean, lint-free gloves, insert the new 2-pin lamp into the lamp socket.

5. Reinstall the inner lens segments and outer lens by reversing the removal procedure.
6. Reinstall the outer lens.
7. Clamp the latch on the outer lens.

WARNING

De-energize the circuit and lock out the circuit or regulator so that the 
circuit cannot be energized by remote means before attempting to service 
the fixture.
• Failure to observe a warning may result in personal injury, death or 

equipment damage.

CAUTION

Touching quartz lamps with bare fingers may seriously shorten lamp life. 
If the quartz lamp has been touched, clean the lamp with tissue moistened 
with isopropyl alcohol.
• Failure to observe a warning may result in equipment damage.

Содержание L-861SE































Отзывы:

Нет отзывов