ADB L-861SE Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 30

ADB L-861SE Скачать руководство пользователя страница 19

© ADB bvba All Rights Reserved

13

2.4.4 Stake Mounting

This section describes procedures for assembling and mounting the stake.

2.4.5 Stake Assembly

To assemble the stake, perform the following procedure:

1. See Figure 6. Attach the stake hub (2) to the metal stake (5) using two 3/8 16 x 3/4-in.

hex head screws (3) and 3/8-in. lockwashers (4).

2. Insert female L-823 secondary connector in cable connector support's forked tine and

attach the cable connector support (7) to the stake hub (2) using 1/4 20 x 3/4-in. hex head
screw (8) and 1/4-in. split lockwasher (9).

NOTE:

The small hole at the lower end of the stake is provided for counterpoise wire

connection.

Figure 4:

Stake Mounting

Lockwasher

Lockwasher

1. L-823 Male Plug

2. Stake Hub

3, 4. Hex Head Screw

5. Metal Stake

6. Transformer Secondary Female Plug

7. Cable Connector Support

8, 9. Hex Head Screw

1. Frangible Coupling and Disconnect Plug

2. Connectors

3. 5 KV, L-824 Cable

4. Metal Stake (30 in.)

5. Concrete Anchor (Recommended 6 x 6 x 12-in.)

6. Optional Bare Copper Counterpoise Wire

7. L-830 Transformer

14-in (35 cm)
Standard

«
...
17
18
19
20
21
...
»

Содержание L-861SE































Отзывы:

Нет отзывов