ADB L-861SE Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 30

ADB L-861SE Скачать руководство пользователя страница 18

L-861SE Clamp Band ERTE
96A0193 Rev. i

Installation

© ADB bvba All Rights Reserved

12

9. Remove the outer globe (1), if installed. Place a level (such as a circle bubble level) on

top of the head assembly and level the light fixture by adjusting the four Phillips head
screws (7) in the lower casting (11).

10. See Figure 5. Place the outer globe on the fixture, and check for outer globe and inner

lens direction.

NOTE:

To verify that the lens is oriented correctly, the arrows on top of the lens must point

to the runway side. Arrows should point toward the runway when the fixture is installed
parallel with the runway or when the fixtures are installed perpendicular to the runway to
mark a displaced threshold. When fixtures are located at the end of the runway, the
arrows should point to the imaginary extension of the runway centerline. Always make
sure that the colored lens location is in compliance with the airport project plans and
specifications.

SIDE

OBSCURED

3 1/2° TOE

LH OBSCURED

RUNWAY

3 1/2° TOE

RH OBSCURED

RUNWAY

«
...
16
17
18
19
20
...
»

Содержание L-861SE































Отзывы:

Нет отзывов