ADB Safegate L-858 AGSF Series Скачать руководство пользователя страница 37

Страница: 37 / 56

Table 10: Cord set Location #2 Parts (continued)

Item

Description

Supplier

Part Number

Note

NOTE A: Refer to Table 3-3 for flexible conduit connectors.

NOTE B: Signs supplied with the following length external to the sign: Size 1 = 47 in. Size 2 = 41 in.

Size 3 = 35 in. Size 4 = 18 in. Size 5 = 35 in. Any other external length requires a separate line on the

purchase order specifying the external length required.

NOTE C: Requires a separate line item on purchase order.

NOTE D: Shown for reference only. Part supplied with sign.

Table 11: Flexible Conduit Connectors

Item

Description

Supplier

3/4-inch (44.45 mm) diameter hole

ADB Safegate

1-1/4 inch (31.75 mm) flexible conduit male

connector

Contractor

1-1/4 inch (31.75 mm) flexible conduit

Contractor

1-1/4 inch (31.75 mm) flexible conduit male

connector

Contractor

1-1/2 x 1-1/4-in. (38.1 x 31.75-mm) hex

reducer bushing

Contractor

3.7.4 Cord set Exit Location #3

Figure 14

shows cord set location #3. Refer to

Table 12

for cord set location #3 parts and part numbers.

Figure 14: Cord set Location #3 (Standard)

Table 12: Cord set Location #3 Parts

Item

Description

Supplier

Part Number

Note

Cord set 16/2 SOW 600 V

ADB Safegate

Not applicable

Cable clamp

ADB Safegate

60A2851

Base flange

ADB Safegate

62A2142 or

62A2146

2-in. (50.8 mm) rigid

conduit

Not applicable

96A0286, Rev. AT, 2020/09/16

Содержание L-858 AGSF Series





















































Результаты поиска

Содержание L-858 AGSF Series

Отзывы:

Похожие инструкции для L-858 AGSF Series

Бренды по названию

Популярные бренды

ADB Safegate L-858 AGSF Series, Руководство пользователя

Результаты поиска

Содержание L-858 AGSF Series

Отзывы:

Похожие инструкции для L-858 AGSF Series

Бренды по названию

Популярные бренды