Adaptec 1737100 - 62044 SGL ENET PCI 4CH Скачать руководство пользователя

Страница: 95 / 190

7-23

Register Descriptions

PMCSR (Power Management Control/Status) Register

Type: R/W

Internal Registers Subgroup: PCI Functional Registers

Byte Address: 54h - 57h

18:16

PMVersion

: This field indicates that there are 4 bytes of General

Purpose Power Management registers implemented as described in
revision 1.0 of the ‘PCI Bus Power Management Interface
Specification’.

15:8

00h

NextItemPtr:

This field provides an offset into the function’s PCI

configuration space pointing to the location of next item in the
function’s capability list. The AIC-6915 does not implement more
items in the list.

7:0

01h

PowerManagementId

: This ID indicates the start of the Power

Management Register Block

Table 7-32. Power Management Control Status Register

Bit(s)

Reset

Value

Description/Function

31:29

PMData:

This function is not implemented. The AIC-6915 does not

provide information about the power it consumes.

23:16

Reserved:

Always read as 0.

r/w

PmeStatus:

This bit is set when the function would normally assert

the PME_ signal independent of the state of the P

bit. Setting

this bit clears it and causes the function to stop asserting a PME_.
Clearing the bit has no effect.

14:13

DataScale:

This function is not implemented. The AIC-6915 does

not provide information about the power it consumes.

12:9

DataSelect:

This function is not implemented. The AIC-6915 does

not provide information about the power it consumes.

r/w

PmeEn:

This bit enables the function to assert PME_. If this bit is

cleared assertion of PME_ is disabled.

7:2

Reserved:

Always read as 0.

1:0

r/w

PowerState

: This 2-bit field determines the power state of the

AIC-6915
‘00’ - D0
‘01’ - D1
‘10’ - D2
‘11’ - D3
Reset Value: In CardBus mode, (when the EPROM A0 pin is
sampled low at reset), the PowerState starts at D3. Otherwise, it
starts at D0.

Table 7-31. Power Management Register (Continued)

Bit(s)

Reset

Value

Description/Function

Содержание 1737100 - 62044 SGL ENET PCI 4CH































































































































































































Результаты поиска

Содержание 1737100 - 62044 SGL ENET PCI 4CH

Отзывы:

Похожие инструкции для 1737100 - 62044 SGL ENET PCI 4CH

Бренды по названию

Популярные бренды

Adaptec 1737100 - 62044 SGL ENET PCI 4CH, Руководство программиста

Результаты поиска

Содержание 1737100 - 62044 SGL ENET PCI 4CH

Отзывы:

Похожие инструкции для 1737100 - 62044 SGL ENET PCI 4CH

Бренды по названию

Популярные бренды