Adaptec 1737100 - 62044 SGL ENET PCI 4CH Скачать руководство пользователя страница 139

Страница: 139 / 190

7-67

Register Descriptions

FunctionEventMask Register

Type: R/W

Internal Registers Subgroup: PCI Functional Registers

Byte Address: 0134h - 0137h

Controls which events cause a status change interrupt. Only bit 15 is implemented,
all other bits are zero.

FunctionPresentState Register

Type: R

Internal Registers Subgroup: PCI Functional Registers

Byte Address: 0138h - 013Bh

Reports the present state of various functions only the interrupt function (bit 15) can
change state. Bit 15 is the only bit implemented.

Table 7-84. FunctionEventMask Register

Bit(s)

Reset

Value

Description/Function

31:16

Reserved:

Always reads 0.

r/w*

Intr:

Interrupt Mask. If set, and bit 15 (I

NTR

) of the F

UNCTION

VENT

14:5

Reserved:

Always reads 0.

GWake:

Always reads 0.

3:2

BVD[2:1]:

Always reads 0.

Ready:

Always reads 0.

WP:

Always reads 0.

Table 7-85. FunctionPresentState Register

Bit(s)

Reset

Value

Description/Function

31:16

Reserved:

Always reads 0.

Intr:

Set to 1 if an interrupt is generated from somewhere in the chip

other than the F

ORCE

UNCTION

14:5

Reserved:

Always reads 0.

GWake:

Always 0. The AIC-6915 does not support wakeup on

CardBus as it requires an external power source.

2:3

BVD[2:1]:

Always 0 x 3 (11b). The card containing the AIC-6915 is

not expected to have batteries, so the battery is considered
“operational”.

Ready:

Always set. The AIC-6915 always indicates it is ready.

WP:

Always cleared. Write protect is not supported.

Содержание 1737100 - 62044 SGL ENET PCI 4CH































































































































































































Результаты поиска

Содержание 1737100 - 62044 SGL ENET PCI 4CH

Отзывы:

Бренды по названию

Популярные бренды

Adaptec 1737100 - 62044 SGL ENET PCI 4CH, Руководство программиста

Результаты поиска

Содержание 1737100 - 62044 SGL ENET PCI 4CH

Отзывы:

Бренды по названию

Популярные бренды