manualshive.com logo in svg

Adaptec 1737100 - 62044 SGL ENET PCI 4CH, Руководство программиста

Поделиться
Скачать
Adaptec 1737100 - 62044 SGL ENET PCI 4CH Скачать руководство пользователя страница 79

7-7

Register Descriptions

PCI Status Register

Type: R/W

Internal Registers Subgroup: PCI Configuration Header

Byte Address: 06h - 07h 

The STATUS register is used to record status information for PCI bus related events. 
Read transactions of the STATUS register access the currently stored status 
information. Write transactions to the STATUS register are not used to store data but 
rather to clear those bits that are set. The STATUS register is forced to be inactive 
when PCI_PCIRST_ is asserted. The STATUS register may be read at any time in 
Configuration, I/O, or memory Space.

If at least one of the status bits: DPE, SSE, RMA, RTA, STA or DPR is asserted and 
the corresponding enable bit, implemented in PCIDeviceConfig register, is also 
asserted, then PCIInt is asserted. PCIInt is an internal interrupt status bit 
implemented in GeneralInterruptStatus register.

0

r/w

0

ISPACEEN: 

I/O Space Enable. Setting this bit enables the 

AIC-6915 to respond to PCI I/O transactions. When ISPACEEN is 
inactive the AIC-6915 does not respond to I/O cycles. 

Table 7-6. PCI Status Register 

Bit(s)

rw

Reset 

Value

Description/Function

15

r/w

0

DPE: 

The Detected Parity Error bit is set when a 36-bit even-parity 

error is detected by the AIC-6915 (as a target) during an Address 
phase or a Write Data phase, and by the transaction master during 
a Read Data phase. DPE is set inactive during and after assertion of 
PCI_PCIRST_

 or by a write to the STATUS register with bit 15 

(=1).

14

r/w

0

SSE: 

Signal System Error. The AIC-6915 sets the SSE bit only when 

PERRESPEN

 and SERRESPEN are set for detected address parity 

errors.

13

r/w

0

RMA: 

Received Master Abort is set when the AIC-6915-generated 

transaction is terminated by the AIC-6915 due to no response from 
the intended target by the sixth (for SAC) or seventh (for DAC ) 
PCLK after the AIC-6915 asserted FRAME_. The AIC-6915 releases 
the bus on the next PCLK and does not retry the transaction. 
Software/firmware intervention is required for the AIC-6915 to 
continue master transactions. RMA is set inactive during and after 
assertion of PCI_PCIRST_ or by a write to the STATUS register with 
bit 13 (=1). 

12

r/w

0

RTA: 

Received Target Abort is set when the AIC-6915, as a PCI bus 

master, generates a transaction terminated with Target-Abort 
indication. RTA is set inactive during and after assertion of 
PCI_PCIRST_

 or by a write to the STATUS register with bit 28 

(=1). When an Target-Abort indication is received, the AIC-6915 
does not retry the transaction and software/firmware intervention 
is required for the AIC-6915 to continue master transactions.

Table 7-5. PCI Command Register  (Continued)

Bit(s)

rw

Reset 

Value

Description/Function

Содержание 1737100 - 62044 SGL ENET PCI 4CH































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды